ABTECH SAFETY TORQ AB2.4T Benutzerhandbuch Seite 2

It is imperative that this TORQ Inertia Reel Fall Arrester is only used for its intended purpose and that it is
subject to an annual recorded service by the manufacturer or an approved service agent.
To avoid personal injury, prior to using this device or training others to use it,
CAREFULLY READ and understand these instructions. If there is anything you do not understand DO NOT use
Certain information in this manual is governed by law and is subject to change without prior notice. Great care
has been taken to ensure that the information is correct at the time of publication. However, it is the user's sole
responsibility to ensure that they fully comply with all legal requirements. Abtech Safety will not accept liability
Abtech Safety operates a policy of continual improvement and reserve the right to change specifications without
notice. The Manufacturer and / or their recognised agents, directors, employees or insurers will not be held liable
for consequential or other damages, losses or expenses in the connection with or by reason of or the inability to
Note; training should only be delivered by a suitably qualified and competent person.
Warning
In order to obtain optimum safety and performance please
study and understand these instructions and receive adequate
training by a trained and competent person before using this
device. If in any doubt whatsoever about the safe use of this
device seek the advice/supervision of a trained and competent
person or contact the supplier. Please retain this information for
future reference.
The consequences of improperly using the device, not following
instructions or markings may be serious injury or death.
Rescue Planning
The end user(s) should anticipate and plan rescue and recov-
ery activities before use as part of a planned Risk Assessment
for each use event and in the event of a fall or other scenario
where rescue and recovery may be required. Speed of rescue
and recovery must be considered as post fall injury can result if
suspension time following a fall is prolonged.
The device is a component part of a Fall Arrest System and may
be issued to anyone who needs to use it on a personal issue
basis. These User Instructions must be issued to the end user
of this device who must maintain a record of the annual
thorough examination on the Inspection Form provided.
Wire specification: 5mm 7X19 Galvanised Steel Wire to
BSEN12385:2002
Model Type Specifications:
Model No. AB2.4T
Line length
Line type 48mm Webbing
BS EN360 2002
Standards ANSI/ASSE
Z359.14-2012
Weight 1.00kg
the device, contact the supplier or Abtech Safety for further details.
for any inaccuracy or incorrectly stated legal requirements.
use the device for any other purpose.
AB6T
2.4m 6m
Galv.
Wire
BS EN360 2002
ANSI/ASSE
Z359.14-2012
4.75kg
.
All work at height including the use of Personal Protective
Equipment (PPE) as a control measure is subject to a
suitable and sufficient risk assessment.
System Requirements and Limitations of Use
This device is intended for use as a Fall Arrest (Fall Arrest
Device) or Recovery (Rescue, Recovery Winch) device and is
not intended for use for work positioning.
Warning: This device must not be used where the terrain and/or
anchorage point is unstable (e.g. grain silo's, shifting sand,
powder, sludge, etc) as a slow descent will not activate the
braking system.
Maintenance
This device has no user serviceable parts and must not be
disassembled or adjusted except by the manufacturer or
approved service agent. User maintenance is limited to pre-use
inspection, cleaning, drying and storage as described in these
User Instructions. When maintenance is required consult the
supplier/manufacturer. Do not tamper with or adjust any part of
the device.
AB10T
10m
Galv.
Wire
BS EN360 2002 BS EN360 2002
ANSI/ASSE
Z359.14-2012 Z359.14-2012
6.25kg
Warning
AB15T AB15RT
15m
Galv.
Wire
BSEN360 2002
BSEN1496 2006
ANSI/ASSE
ANSI/ASSE
Z359.14-2012
8.75kg 10.40kg
15m
Galv.
Wire