Simplified Eu Declaration Of Conformity - Elkron RC600 Installations-, Programmier- Und Gebrauchsanleitung

ENGLISH
The remote control RC600 with control feedback on indicator LEDs (version 2) is used to arm (totally or partially) and to disarm
the system; it can also be used to send a panic alarm.
Part identification
1.
BUTTON
Press this button to arm the system totally.
2.
BUTTON
Press this button to disarm the system.
3.
BUTTON
Press this button to arm the system partially (the button may be
associated with only one partial arming setting: A or B or C).
4.
BUTTON
Hold this button pressed for 3 second to send a panic alarm regardless of system state.
< < N N O O T T E E > >
Once activated, the panic alarm cannot be blocked by pressing the off button. To block the alarm, it is necessary
to send a deactivation control either from the app or from the keypad or from a second remote control. The
alarm will be interrupted whenever the set timeout is reached.
5.
TWO-COLOUR LED INDICATION
The LED can provide the following information to the user when the remote control buttons are pressed:
•
the arm/disarm control was run by the control unit: the red LED will blink and then turn briefly green to indicate correct
implementation
•
the arm/disarm control was NOT run by the control unit: the LED stays red for 2 seconds. This may be the case in
which the system displays a fault upon arming, such as an open access door contact. In this case, the user can choose
to arm the system all the same by pressing the arm button again
•
a panic alarm was activated: the red LED will blink quickly 6 times without further indications
•
the remote control is out of range of the control unit: the red LED will blinked three times
6.
BATTERY HOUSING
The remote control is powered by a CR2032 3 V lithium battery. The flat battery signal sent to the control unit during normal
signal transmission and the control unit will display the respective state.
< N O T E >
< N O T E >
When replacing the battery, after having removed the flat battery, press any button twice to discharge the device
completely before inserting the new battery.
If a flat battery is inserted, the LED will blink three times to indicate it.
Preparation
Remove the cover from the battery.
Insert the battery with the side without marking (negative) facing downwards.
Close the cover.
Start the learning function on the control unit; see the control unit manual for more information.
Press any button on the remote control.
The respective information will be displayed if the control unit receives the remote control signal correctly.
Refer to the manual of the control unit to complete the learning process.
Technical
specifications
Power supply: 1 lithium battery CR2032 3V
Battery life: 3 years (typical value, may vary according to use)
Two-way radio frequency: 868 MHz
Working temperature range -10°C to +45°C
Dimensions: 50 X 33 X 14.5 mm
Weight: 60g
Certification EN 50131 Degree 2, Class Ⅱ
Hereby, URMET S.p.A. declares that the radio equipment type: REMOTE CONTROL RC600 is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.elkron.com.
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste electrical and
electronic equipment (WEEE).
The symbol of the crossed-out wheeled bin on the product or on its packaging indicates that this product must not be
disposed of with your other household waste.
Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for
the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment
at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects
human health and the environment.
For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your
household waste disposal service or the shop where you purchased the product.
4

SIMPLIFIED EU DECLARATION OF CONFORMITY

ELKRON
Tel. +39 011.3986711 - Fax +39 011.3986703
www.elkron.com – mail to: info@elkron.it
ELKRON is a trademark of URMET S.p.A.
Via Bologna 188/C – 10154 Turin (TO) Italy
www.urmet.com
DS80TX44-001C
MADE IN TAIWAN