Safety Warnings - Makita DGA417 Betriebsanleitung

Work mode: disc sanding with normal side grip
Work mode: disc sanding with anti vibration side grip
NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and
may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures to protect the operator that are based on an estimation
of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the
times when the tool is switched off and when it is running idle in addition to the trigger time).
WARNING:
The declared vibration emission value is used for main applications of the power tool. However if
the power tool is used for other applications, the vibration emission value may be different.
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings
WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Model
DGA417
DGA418
DGA467
DGA468
DGA515
DGA517
DGA518
Model
DGA417
DGA418
DGA467
DGA468
DGA515
DGA517
DGA518
Vibration emission (a
h, DS
2
2.5 m/s or less
2
2.5 m/s or less
2
2.5 m/s or less
2
2.5 m/s or less
2
2.5 m/s or less
2
2.5 m/s or less
2
2.5 m/s or less
Vibration emission (a
2
(m/s )
2
2.5 m/s or less
2
2.5 m/s or less
2
2.5 m/s or less
2
2.5 m/s or less
2
2.5 m/s or less
2
2.5 m/s or less
2
2.5 m/s or less
Cordless grinder safety warnings
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
This power tool is intended to function as a
1.
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2. Operations such as polishing are not recom-
mended to be performed with this power tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool manufac-
turer. Just because the accessory can be attached to
your power tool, it does not assure safe operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
10 ENGLISH
2
) : (m/s ) Uncertainty (K) : (m/s
1.5
1.5
1.5
1.5
1.5
1.5
1.5
) : Uncertainty (K) : (m/s
h, DS
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
)
2
)