Petra electric KM 30 Gebrauchsanweisung Seite 15

out paper filters.
19 Fill in coffee or espresso powder. The powder
cartridge contains 5.5 to 7.5 g depending on the cof-
fee quality. This is sufficient for one cup of coffee.
20 Press the powder lightly and scrape off at the fil-
ling edge. If too much is filled in, the brewing cham-
ber cannot be closed.
21 Press the lid (22) open and remove any powder
residue adhering to the exterior.
Remove any powder residue adhering to the
exterior thoroughly; they can plug up the pad cassette
(7). The rocking lever (5) then can no longer move to
the right to remove the pad cassette (7). If this should
occur, despite observing the instructions, please pro-
ceed as described at the end of this user manual in
section "Help in case of malfunctions."
22 Place the powder cartridge into the pad cartridge
in the compartment for 2 pads and
brewing chamber (6)
15 When the display
brewing (green), press on the start button
23 Empty the powder cartridge after brewing. The fil-
ter paper is also bio-degradable as is the coffee pow-
der.
24 25 Rinse the powder and pad cartridge after
every brewing cycle.
Routinely check that the center opening of the
pad cartridge is free (7).
Change coffee quantity
The quantity of coffee powder is optimally adjusted to
one cup in one pad or in the powder cartridge. You
can vary the filling quantity per cup according to your
personal desires and therefore change the strength of
the coffee.
The automatic coffee pad appliance offers the com-
fortable option to individually program the desired cof-
fee quantity for every starting button
1. Insert the pad as described above, press the rocking
lever (5) in the area as far left as possible and
wait until the brewing readiness
green.
2. Hold the start button to be programmed
(3 to 4 seconds) until the display
green. During brewing, the programming mode is
active. Watch how the cup fills up. Press the start
button again when the desired quantity is reached.
The brewing stops and the brewing period (active
period of the pump) is programmed. Each new
brewing cycle with this start button now always
10 lock the
.
signals the readiness for
or
is displayed in
occurs at the same brewing period. The prepared
coffee quantity will only vary slightly depending on
the coffee quality.
Information concerning the programming
mode:
The programming mode is active for a maximum of
30 seconds
brewing. If you do not press the start button before
brewing ends automatically, the maximum possible
filling quantity will be programmed.
Restore the standard filling quantity
In order to restore the filling quantity to the delivery
state, proceed as follows:
1. Switch the appliance off,
2. Hold the start button
both displays
Shut-off
The appliance can be switched off at any time by
.
pressing the ON/OFF button
on, it is automatically shut off after 60 minutes of the
previous use. The power consumption is less than
0.5 Watts during off-mode.
Filling level display
The fresh water content is constantly monitored by a
movable floating capsule in the water tank (3). The
display
quired minimum filling quantity. The operation is continu-
ed as soon as you replace the filled water tank (3).
Decalcification
The appliance must be routinely decalcified as all
hot water appliances. In order to accomplish this, use
the special decalcifier durgol
.
be obtained from select dealers. If you wait too long
with the decalcification, damages cannot be ruled out.
The following details are guidelines. If you decalcify
earlier, when the crema of the coffee is no longer
optimal, when the coffee quantity is reduced noticea-
or
bly at the same setting or when the outlet (8) drips
flashes
during heating.
15
or 60 seconds
(3 to 4 seconds) until
and briefly flash.
. If it remains switched
flashes red when underrunning the re-
®
swiss espresso
during
®
; it can