LIVARNO Z30846 Montageanleitung

Bedside Table
Introduction
Before assembling and using the product
for the first time, take time to familiarise
yourself with the product first. Read the
following assembly instructions and safety instruc-
tions carefully. Only use the product as described
and for the designated areas of application. Please
keep these instructions in a safe place. If you hand
this product on to a third party, you must also pass
on all documents relating to the product.
Proper Use
The product is suitable for storing and keeping safe
small and lightweight objects. It is designed for use
in private, dry, indoor areas. Any use other than previ-
ously mentioned or any product modification is pro-
hibited and can lead to injuries and / or product
damage. The manufacturer is not liable for any dam-
ages caused by any use other than for the intended
purpose. The product is not intended for commercial
use.
Description of parts
and features
Top panel
1
Right side panel
2
Trim
3
Bottom connection piece
4
Back panel
5
Left side panel
6
Top connection piece
7
Back / sides (drawer), preassembled component
8
Bottom (drawer)
9
Front (drawer)
10
Wooden dowel (approx. ø 7.8 x 30 mm)
11
Cam pin (approx. ø 6 x 36 mm)
12
Cam connector (approx. ø 15 x 12 mm)
13
Drawer handle
14
Cross-head screw (approx. ø 4 x 20 mm)
15
64100_liv_Beistellkommode_Content_LB3.indd 3
Metal drawer runner
16
Cross-head screw (approx. ø 4 x 10 mm)
17
Dowel (approx. ø 6 x 30 mm)
18
Cross-head screw (approx. ø 3.5 x 40 mm)
19
Wooden dowel (approx. ø 5.8 x 30 mm)
20
Cam pin (approx. ø 6 x 25 mm)
21
Cam connector (approx. ø 12 x 10 mm)
22
Cam pin (approx. ø 6 x 36 mm)
23
Cross-head screw (approx. ø 4 x 9 mm)
24
Back panel restraint
25
Cross-head screw (approx. ø 2.5 x 16 mm)
26
Cap
27
Supply Scope
Immediately after unpacking, check that the delivery
is complete and that the product and all its parts are
in perfect condition. Do not under any circumstances
assemble the product if the delivery is incomplete.
1 Top panel
1 Right side panel
1 Trim
1 Bottom connection piece
1 Back panel
1 Left side panel
1 Top connection piece
3 Back / sides (drawer), preassembled components
3 Bottoms (drawer)
3 Fronts (drawer)
13 Wooden dowels (approx. ø 7.8 x 30 mm)
6 Cam pins (approx. ø 6 x 36 mm)
8 Cam connectors (approx. ø 15 x 12 mm)
3 Drawer handles
3 Cross-head screws (approx. ø 4 x 20 mm)
6 Metal drawer runners
18 Cross-head screws (approx. ø 4 x 10 mm)
2 Dowels (approx. ø 6 x 30 mm)
2 Cross-head screws (approx. ø 3.5 x 40 mm)
12 Wooden dowels (approx. ø 5.8 x 30 mm)
6 Cam pins (approx. ø 6 x 25 mm)
6 Cam connectors (approx. ø 12 x 10 mm)
2 Cam pins (approx. ø 6 x 36 mm)
6 Cross-head screws (approx. ø 4 x 9 mm)
4 Back panel restraints
4 Cross-head screws (approx. ø 2.5 x 16 mm)
Introduction
GB/IE 3
06.05.11 16:44