Alarm Function; Cleaning And Maintenance - AEG SR 4372 Bedienungsanleitung

English
46
DAB Menu
• Full scan: Starts the station scan. The DAB frequency
band is scanned for stations.
• Manual tune: To do so you need to know the station
frequency. This can be found on the internet site of the
broadcasting service. Select individual frequencies using
the / buttons (3/11).
• DRC: short for Digital Range Control (dynamic range).
The term DRC describes the ratio between the quietest
and the loudest sound. If the dynamic range is very high
there are very soft sounds as well as very loud sounds. Un-
der some circumstances this may present a problem with
playback. Let us assume that you are listening to a radio
station in a relatively loud environment. By increasing the
volume you can play the quiet sections louder. This how-
ever has the disadvantage that the loud sections become
uncomfortably loud. It makes sense here to reduce the
dynamic range. Select between the options:
– DRC off: The dynamic range is not reduced.
– DRC low: The dynamic range is slightly reduced.
– DRC high: The dynamic range is sharply reduced.
• Prune: It may be that you can no longer receive some
stations after a station scan or change of location. With
this function you can delete these stations from the
reception list. Select "YES" and confirm with the
ENTER button.
Standardized menu for all operating modes
• Clock Set: Set the time and the date manually.
• Language Set: Change the OSD language. The selected
language will be marked with .
• Sleep Set: Set the time after which the device will switch
off automatically. Available options: 10, 20, 30, 60, 90, and
120 minutes. Setting OFF will deactivate this function.
NOTE:
When activated, the " " icon will appear in the display.
• Reset: Select the "YES" command if you want to reset
the device again to the factory defaults. All settings which
you have made will be lost.
• Software version: Here, you can display the Software
Version of the device.

Alarm function

You can set the device in such a way that it switches on at a
specific time. You may set two alarm times.
• To select an option, press the /
• Select an option with the
/ /
buttons (3/11).
/ / ENTER button (5).
Setting the alarm time
Press the ALARM / SNOOZE button
– 1x = to set the first alarm time
– 2x = to set the second alarm time
Setting alarm time 1 is described below
1. Press the ALARM / SNOOZE button (6). "Alarm1: BEEP-
ER1" appears in the display and "OFF" starts flashing.
Select option "ON". The hours will be flashing.
2. Alarm1 Time Set: Now set the alarm time.
3. Alarm1 Mode: Select the time at which the alarm time
needs to be activated. Select from: DAILY, ONCE, WEEK-
ENDS, WEEKDAYS.
4. Alarm1 Type: Select a source by which you want to be
awakened. Select from: BEEP Tone1, BEEP Tone2 (beep),
DAB, FM.
NOTE: Important!
• Remember to set the desired volume using the
control (7). The device will switch on with the vol-
ume setting used last.
• When selecting DAB or FM, remember to tune in
the desired station. The device will switch on with
the radio station tuned in last.
The activated alarm function is shown on the display by the
" / " symbol.
Turn off the alarm signal
To shut off the alarm signal, press the
(5).
Snooze
The automatic alarm function can be turned off for 9 minutes.
NOTE:
When activated, the " " icon appears in the display.
Deactivate alarm function
1. Press the ALARM / SNOOZE button (6) once or twice
respectively.
2. Select option "OFF". The " " icon or " " icon disap-
pears.

Cleaning and Maintenance

CAUTION:
Do not immerse the device in water.
• Always remove the mains plug before cleaning the
machine.
• Any marks on the surface can be wiped off with a slightly
damp cloth without any additives.
/ / ENTER button