General Information; Safety Instructions - Renkforce 1176533 Bedienungsanleitung

G Operating Instructions
renkCast Wireless TV-Stick
Item no. 1176533
Intended use
This device is intended for the wireless streaming of content from your computer,
smart phone or tablet to a display device with an HDMI
Also, the product can display the screen content of your smart phone or tablet
equipped with Android or Apple iOS on your HDTV for example.
HDMI is a registered trademark of HDMI Licensing L.L.C.
Read these operating instructions completely and carefully. They contain a lot of im-
portant information about operation and use. Observe all safety instructions!
Contents
• renkCast-Stick
• Micro USB cable for power supply
• HDMI extension cable
®
• Operating instructions
Safety Instructions
D amages due to failure to follow these operating instructions will void the
warranty. We assume no liability for any consequential damage!
W e do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions. The warranty
will be void in such cases!
Dear customer,
The following hazard information and safety instructions are intended to
protect your health and also to protect your device.. Please read the follow-
ing points carefully:
• Maintenance or repair works should only be performed by a qualified per-
son or a specialist workshop.
• The product is only suitable for dry, enclosed indoor areas. Do not expose
to direct sunlight, heat, cold, humidity or moisture; otherwise it may be
damaged.
• The product is not a toy. Position the product so it is out of the reach of
children.
• When the product is taken from a cold room to a warm room (e.g., during
transport), condensation may be produced.
Allow the product to reach room temperature before you connect it to the
power supply. This may take several hours.
• Handle the product with care. The product can be damaged if crushed,
struck or dropped, even from a low height.
• Safe operation can no longer be assumed if:
- the device is visibly damaged
- the device no longer works
- the device has been stored under adverse conditions for a long time
- it was exposed to heavy loads during transport
• Disconnect the product from the power supply, if it is not used for an ex-
tended period of time (e.g. storage).
• Do not leave packaging material lying carelessly; it could become a dan-
gerous plaything for children.
• If you have any questions that are not answered in these operating in-
structions, please contact our technical support centre or consult a pro-
fessional.
connection.
®
General Information
• The program or application software and features are continuously developed fur-
ther. Therefore update your program or software application and also the firmware
at regular intervals.
• It may well be, that over time the operational features may change due to updates.
Therefore, please always follow the instructions or information displayed on the
monitor connected to your device.
• The current software version for Windows
operate the current program or software application are available on the website:
www.iezvu.com.
• Establishing a connection, for example with to Miracast, may take up to several
seconds on some devices.
• In case the stick is not responding, simply unplug from the HDMI
nect the power supply. Reconnect after several seconds. After that it should work
as usual.
Connection and Getting Started
• First unpack the product and its accessories.
• Connect the included micro USB cable to the corresponding port on the sticks. This
is intended for the supply of current.
• Basically, the stick is compatible with any display device equipped with HDMI
Now plug it into a vacant HDMI
ple. In the course of the description, we consider that the device is operated on a TV
set.
If the terminal is not freely accessible use the included HDMI
cable.
• Now connect the USB cable, that you have connected before to the micro USB port
on the stick, to a vacant USB terminal on your TV.
The USB port is intended only to supply current. A minimum of at least
500 mA must be provided.
Most conveniently, if your device connected to the stick is also equipped
with a USB terminal. Equally possible is the use of a 5 V USB adaptor.
• Finally, switch the TV on.
The blue LED on the stick should start to glow. If this is not the case, then use a dif-
ferent USB port or an external USB adaptor to supply power.
• The splash screen will be displayed on your TV screen after a few seconds. Before
that, you may need to switch to the correct HDMI
Please also follow the instructions for your TV set.
Configuration
All important information that you may need for further configuration is dis-
played on the home screen.
Please note, that this configuration may change due to updates.
In the course of the following description, we consider that the configuration
is carried out on a tablet.
• First download and install the appropriate program or application software for the
device you intend to use with the stick.
To do this, follow all of the instructions.
You may need to allow the program in your PC's firewall.
The current download location, or what exactly you should enter in the store's
search box, is displayed on your TV screen.
• Next, connect the WLAN of your tablet to the WLAN of the stick. SSID and password
are also shown on your screen.
Always make sure that your device is connected to the WLAN of the stick.
After a restart following the configuration of the stick, it occasionally hap-
pens that your tablet connects automatically to your Wi-Fi network.
• After that start the software application.
• Register your device on your home network for internet connections first and check
if any updates are available before you use the device.
• See settings under Internet for information on how to register your Internet connec-
tion. It may also be that this will be automatically displayed during the configuration
process.
• Select your Wi-Fi network and enter your password.
• Then proceed to update your firmware, if necessary.
• We also recommend you to check whether the correct resolution is selected. Ad-
just, if necessary.
• Now you can use your stick. The operation is basically self-explanatory. Simply fol-
low the information displayed on your screen. Application software or program help
is available on the website: www.iezvu.com.
and MacOS, and also help features to
®
®
terminal on your TV set or your monitor for exam-
®
input.
®
port and discon-
input.
®
extension
®