Maintenance - Makita DRV150 Betriebsanleitung

Available blind rivets
NOTICE:
Using nose piece, jaw, jaw pusher, or pipe that does not match the mandrel diameter may cause
poor fastening, clogging of the mandrel, or malfunction of the tool.
Refer to the table below for the combination of rivet, nose piece, jaw, jaw pusher, and pipe.
NOTE: Some items in the table may be included in the tool package as standard accessories and some items in
the table are provided as optional accessories. They may differ from country to country.
For DRV150
Rivet
Size Diameter of
mandrel
ø2.4 mm ø1.4 -
(3/32") 1.6 mm
ø3.2 mm ø1.8 -
(1/8") 2.1 mm
ø4.0 mm ø2.2 -
(5/32") 2.6 mm
ø4.8 mm ø2.6 -
(3/16") 3.2 mm
*. Pipe is not necessary for operation.
For DRV250
Rivet
Size Diameter of
mandrel
ø2.4 mm ø1.4 -
(3/32") 1.6 mm
ø3.2 mm ø1.8 -
(1/8") 2.1 mm
ø4.0 mm ø2.2 -
(5/32") 2.6 mm
ø4.8 mm ø2.6 -
(3/16") 3.2 mm
ø6.0 mm ø3.1 -
(1/4") * 3.5 mm
ø6.4 mm ø3.5 -
(1/4") * 3.9 mm
*. Stainless steel rivet is not available.

MAINTENANCE

CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Nose piece
Mark on Hole
nose piece diameter
2.4 ø1.9 mm
3.2 ø2.4 mm
4.0 ø3.0 mm
4.8 ø3.6 mm
Nose piece
Mark on Hole
nose piece diameter
2.4 ø1.9 mm
3.2 ø2.4 mm
4.0 ø3.0 mm
4.8 ø3.6 mm
6.0 ø4.0 mm
6.4 ø4.4 mm
Mark on jaw Jaw pusher
Hole
diameter
4.8 ø1.9 mm
4.8 ø2.5 mm
4.8 ø3.1 mm
4.8 ø3.6 mm
Mark on jaw Jaw pusher
Hole
diameter
4.8 ø1.9 mm
4.8 ø2.5 mm
4.8 ø3.1 mm
4.8 or 6.4 ø3.6 mm
6.4 ø4.0 mm
6.4 ø4.6 mm
Cleaning the jaws and jaw case
Interval of cleaning: Every 3,000 installations of rivet
If the dust is accumulated, it deteriorates the movement
of jaws and may accelerate wear of jaws and jaw case.
To clean the jaws and jaw case, follow the steps below.
1. Remove the jaw case. For the removal procedure,
refer to the removal instructions for the head assembly.
2. Remove the jaws from the jaw case.
► Fig.13: 1. Jaw case 2. Jaw
3. Clean the jaws and jaw case with a brush.
Remove metal powder clogged between the teeth of the
jaws.
4. Apply molybdenum disulfide based grease evenly
to the inner periphery of the jaw case.
► Fig.14: 1. Area to apply grease 2. Jaw case
8 ENGLISH
Pipe
Color Hole
diameter
Gray ø2.2 mm
Black ø2.6 mm
Gray None *
Black None *
Pipe
Color Hole
diameter
Gray ø2.2 mm
Black ø2.6 mm
Gray ø3.4 mm
Black ø4.1 mm
Gray ø4.1 mm
Black ø4.5 mm
Color
Silver
Black
–
–
Color
Silver
Black
Silver
Black
Black
Silver