Operating Mode; Maintenance Instructions; Assembling And Disassembling - Desoutter MC series Bersetzung Der Originalbetriebsanleitung

6159933770
Issue no : 07
Series : -
Original instructions.
© Copyright 2019, Ets Georges Renault
44818 St Herblain, FR
All rights reserved. Any unauthorized use
or copying of the contents or part thereof
is prohibited. This applies in particular to
trademarks, model denominations, part numbers
and drawings. Use only authorized parts. Any
damage or malfunction caused by the use of
unauthorised parts is not covered by Warranty or
Product Liability.
STATEMENT OF USE
Tool suitable for industrial environment only. It
shall be used for tightening or loosening joints in
wood, metal or plastic material. No other use will
be permitted. For professional use only.
DATA
(See page 3).
Sound pressure level:
● < 70 dB(A) (EN 60745-2-2).
● Uncertainly: 3dB(A).
Vibration value:
● < 2.5 m/s² (EN 60745-2-2).
Declaration of noise and vibration emission
All values are current as of the date of this
publication. For the latest information please visit
desouttertools.com.
These declared values were obtained by
laboratory type testing in accordance with the
stated standards and are suitable for comparison
with the declared values of other tools tested
in accordance with the same standards. These
declared values are not adequate for use in risk
assessments and values measured in individual
work places may be higher. The actual exposure
values and risk of harm experienced by an
individual user are unique and depend upon
the way the user works, the workpiece and the
workstation design, as well upon the exposure
time and the physical condition of the user.
We, Desoutter, cannot be held liable for the
consequences of using the declared values,
instead of values reflecting the actual exposure,
in an individual risk assessment in a work place
situation over which we have no control.
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed.
An EU guide to managing hand-arm vibration
can be found at http://www.pneurop.eu/uploads/
documents/pdf/PN3-02-NV_Declaration_info_
sheet_0111.pdf
We recommend a programme of health
surveillance to detect early symptoms which
may relate to noise or vibration exposure, so
that management procedures can be modified to
help prevent future impairment.
14 / 60
REQUIREMENTS
These tools need to be used with controllers
from Desoutter range.

OPERATING MODE

Before using the tool, make sure that it is in
perfect working order and that the controller
is programmed correctly, to reduce the risk of
injury to the operator as a result of unexpected
behaviour of the tool.
When integrating the nutrunner, the adequate
protection is to be worn to avoid any risk of
being dragged by the spindle.
Correctly size the baseplate of the nutrunner so
that it can withstand the reaction torque (see
page 9).
For correct operation of the sensor, the tool
must be fastened on the baseplate using the
appropriate flange. Make sure there is no
other contact point of the tool housing with the
baseplate (electric motor and gearbox).

MAINTENANCE INSTRUCTIONS

● Maintenance should be performed by
qualified personnel only.
● Prior to any maintenance task: disconnect
the tool.
● When disassembling / reassembling the tool,
take the following precautions:
- check that the controller is switched off,
- disconnect the cable.
● To avoid damaging the tool during
disassembly, use the recommended tools.
● When disassembling the handle, be careful
not to pull on the electric wires that are
connected to the motor.
● Any repair on the motor shall be carried out
in our workshops.
When disposing of components,
lubricants, etc ... ensure that the
relevant safety procedures are carried
out.

ASSEMBLING AND DISASSEMBLING

Proceed with assembly or disassembly of the
tool by following the instructions in the technical
manual available on:
http://cadfiles.desouttertools.com - Section
Documentation.
According to Directive 2012/19/
CE concerning Waste Electrical and
Electronic Equipment (WEEE), this
product must be recycled.
● Contact your Desoutter
representative or consult the website
"www. desouttertools.com" to find out
where you can recycle this product.
01/2019