No Visible Light Or Diffuse Light; Transmitted By The Aiming Beam; Replacing The Battery; Replacing The Fiber Optic Handpiece - DenMat SOL Gebrauchsanweisung

NO VISIBLE LIGHT OR DIFFUSE LIGHT

TRANSMITTED BY THE AIMING BEAM

Illumination from the SOL aiming beam can be used to
verify that there are no cracks or breaks in the system
main fiber or single use tips. Visible light should be
transmitted from the tip and a
round spot should be visible, (see page 9).
If there is NO VISIBLE LIGHT start by replacing the
single use tip. If there is still NO VISIBLE LIGHT this
is an indication that the system main fiber has been
damaged. See Replacing The Fiber Optic Handpiece in
the following section.
If the spot is diffuse or not round in shape, the single use
fiber may be defective. Replace it and try again. If the
spot is still diffused or not round in shape the system main
fiber may need to be replaced.
The extent to which differences in the shape of the
spot will be noticed on tissue interaction is dependent
on any reduction in transmission. If the spot has a small
unfocused effect it may still work as expected or the
fiber might need to be replaced.

REPLACING THE BATTERY

The following procedure is provided in the unlikely event
that the system battery needs to be replaced.
WARNING FOR BATTERY REPLACEMENT: Replace
battery ONLY with SOL Replacement Battery item
number authorized by DenMat. Use of a different battery
may present a risk of fire or explosion. Keep away from
children.
Charge battery only after it is properly installed in the SOL
system and only with the SOL AD/DC Power Converter
supplied with the system or Replacement SOL AC/DC
Power Converter item number authorized by DenMat.
CAUTIONS FOR PROPER BATTERY DISPOSAL: The
<100Wh Lithium Ion rechargeable battery used in the
DenMat SOL is recyclable and contains 0% mercury, 0%
lead, 0% cadmium.
Battery must be recycled or disposed of properly.
State and local regulations concerning the recycling and
disposal of Lithium Ion batteries vary so it is necessary
understand and remain in compliance with these
regulations when replacing the SOL system battery.
well formed and focused
(Fig. 7.0)
Please follow the disposal and recycle symbols on the
battery label to ensure that it is disposed of properly in
accordance with local laws and regulations.
The manufacturer of the battery pack is a member of the
Rechargeable Battery Recycling Corporation & the battery
bears the RBRC symbol which includes the phone number
to call to find your closest recycling location. The battery is
accepted for recycling at all RBRC locations throughout
North America. We encourage the use of recycling facilities
for our products. For more information on Lithium Ion
battery recycling:
In North America contact the Rechargeable Battery
Recycling Corporation (RBRC) at:
www.call2recycle.org or phone 1-877-2-RECYCLE
(1-877-273-2925)
In Europe contact the European Portable Battery
Association (EPBA). www.epbaeurope.net
INSTRUCTIONS:
DISCONNECT THE SYSTEM FOOT SWITCH USED FOR
LASER ACTIVATION.
VERIFY THE SYSTEM POWER AND KEY SWITCH ARE
IN THE OFF POSITION.
1) Place the system on its side as shown resting on a soft
towel to prevent scratching. Using a 3/32 size Hex Tool
remove four rubber feet from the bottom and remove the
battery access panel.
2) Remove the battery. NOTE: Replace with new battery
and attach bottom access panel.
REPLACING THE FIBER OPTIC HAND PIECE
(Fig. 8.0)
CAUTIONS FOR OPTICAL FIBER REPLACEMENT: THE
FOLLOWING REPAIR SHOULD ONLY BE PERFORMED BY
A QUALIFIED LASER SERVICE TECHNICIAN.
USE THE REMOTE INTERLOCK FEATURE AS A SAFETY
PRECAUTION DURING FIBER REPLACEMENT.
DISCONNECT THE SYSTEM FOOT SWITCH USED FOR
LASER ACTIVATION.
VERIFY THE SYSTEM POWER AND KEY SWITCH ARE IN
THE OFF POSITION.
11 11