Foot Switch Connector; Remote Interlock Connector; Quick Start Instructions; Sol Quick Start Instructions - DenMat SOL Gebrauchsanweisung

FOOT SWITCH CONNECTOR

The foot switch is used to activate the laser. Install the plug
on the foot switch cable to the corresponding connector on
the rear of the system.
PORT FOR FUTURE EXPANSION. DO NOT USE
(Fig. 4.5)

REMOTE INTERLOCK CONNECTOR

The remote interlock is used to turn the laser OFF when
the door into the room is opened. Remote interlock
operation requires a Door Interlock Switch (not included)
to be purchased from a local electronics store. This
function is explained fully under Remote Door Interlock.
G QUICK START INSTRUCTIONS

SOL QUICK START INSTRUCTIONS

During initial setup use the AC/DC power supply for
up to four hours to fully charge the battery. Plug the
power supply into an AC outlet and connect to the
corresponding connector on the rear of the system.
1.
Plug the foot switch into the connector on the rear of the system.
2.
Insert the key switch and turn to the ON position.
3.
Turn the power switch to the ON position.
4.
System powers up to default Standby Mode 0.8 Watt CW laser setting
5.
Option: Adjust Power using Up and Down Arrow keys
6.
Option: Enter Pulse Mode by pressing Pulse key
7.
Option: Select one of four system presets with the corresponding key
8.
Option: Adjust the preset as described in 5 and 6 above
9.
Press Ready and note audio and visual indicator confirmations
10.
Use the foot switch to activate the laser
H CONTROLS, OPERATION & USE
SOL SMART PRESETS
SOL is delivered with five laser output settings programmed
into the Default Mode when the system is turned
ON and Four Preset Procedure Keys; Cut, Sterilize,
Periodontal and Custom. These settings are typical for the
corresponding procedures with a diode laser. All five can be
reprogrammed with your favorite CW output from .10 to 3.0
watts in .10 watt increments or Pulse output from .10 to 5.0
watts in .10 watt increments. The Default Mode when the
system is turned ON provides the fastest way to start lasing.
After turning the system ON use the default power setting,
6 6
(Fig. 4.4)
(Fig. 4.6)
(Fig. 1.1-1.4)
or adjust, press READY and start lasing. SOL is smart and
remembers the last mode (CW or Pulse) and power setting
so the next time the system is powered up it returns to your
most commonly used or Favorite Setting.
SOL DEFAULT MODE WHEN THE SYSTEM
IS TURNED ON
When the system power and key switches are placed to
the ON position SOL system controls default to the factory
preset Standby Mode 0.8 Watt CW
laser settings are changed the SOL will "remember" those
settings upon exiting and they will become the default for
the next session until changed again. Each subsequent
change in settings becomes the new default. Adjust the
laser CW power Up/Down using the Up or Down arrow
keys select the Pulse Mode and adjust laser power Up/
Down or enter one of four system presets to begin lasing.
Press the Ready key to enter the Ready Mode. Press the
Foot Switch to activate the laser. Return to the original
default, or any other setting, by entering those settings.

SOL PRESETS

See 1.1-1.4
The laser power and output modes, CW and Pulse, for four
typical diode laser procedures are loaded into four button
selections labeled Cut, Sterile, Perio
settings are as follows:
PRESET POWER
Cut 1.2 Watts
Sterile 1.5 Watts
Perio 0.4 Watts
Custom 1.5 Watts
Press any key to select that preset. When the preset is
selected the laser power setting, (in watts), is displayed
and the Pulse Mode illumination is ON if Pulse has been
programmed for that preset. The laser power can be
adjusted with the Up and Down Arrow keys. Pulse and
CW can be selected by pressing the Pulse On/Pulse Off
key. When the system is in the Pulse Mode the Pulse Icon
(1.10) next to the key illuminates alerting the operator
that the Pulse Mode is active. Changes to the laser output
and CW/Pulse modes can be saved as a new preset by
pressing and holding down the key for 3 seconds. If new
settings are not saved (programmed) into the preset by
holding the key for 3 seconds the original default settings
will be retained upon exiting.
laser setting. If the
and Custom. Default
DELIVERY MODE
Continuous Wave (CW)
Pulse
Continuous Wave (CW)
Continuous Wave (CW)