Arcam CDS27 Handbuch Seite 8

AMP Device Mode TUN Device Mode
The A Device Mode button configures the CR902 to The T Device Mode button configures the CR902 to
control your Arcam amplifier. Pressing this button does control the tuner functions of Arcam tuners.
not affect the currently selected input on the amplifier.
P
Toggles power between standby and on
P Toggles power between standby and on
The numeric keys are used to store and
0 9
...
recall presets
Cycles through the front panel display's
DISP
brightness options
Cycles through the front panel display's
DISP
brightness options
Cycles through the display modes on the
MODE
front panel
Cycle through different information
INFO
display modes
Displays the amplifier setup menu on the
MENU
front panel
)
Rewind iPod
Navigate menus (
Fast forward iPod
O confirms a selection
Preset down/Sirius category down/iPod
]
track back
@ Toggles the mute function of the amplifier
Preset up/Sirius category up/iPod track
[
adjusts the volume of an Arcam
Vol +/– forward
amplifier up or down.
#
Vol- Stop iPod
Press the button once to mute an
MUTE
Vol+
Arcam amplifier. Press again (or use ) $ Play/pause iPod
Vol +/–
to un- mute.
&
Play/pause iPod
Toggles Speaker 1 output
SP1
Displays the tuner setup menu on the front
MENU
Toggles Speaker 2 output panel
SP2
Adjusts the balance between the left and ' , Preset up/down, iPod track back/forward
BAL
right audio channel
< > Decrement/increment tuning frequency
O
Confirm a selection
Toggle FM mode between mono and
FM MONO
stereo reception
Enter/Exit Preset recall mode
P/TUNE
Enter/Exit Preset store mode
STORE
Cycles through available tuner bands
BAND
NOTE
The CR902 is a multi-device remote, therefore key
functions will differ according to the last input
button pressed.
Please ensure "CD" button is selected prior to
controlling the CDS27.
CD Device Mode BD Device Mode
The c Device Mode button configures the CR902 to The � Device Mode button configures the CR902 to
control the CD functions of Arcam CD players. control the BD functions of Arcam BD players.
P
P Toggles power between standby and on Toggles power between standby and on
!
Open/close disc tray
! Open/close disc tray
The numeric keys allow direct access to
The numeric keys allow direct access to
individual tracks on a disc. To select a track
individual tracks on a disc. To select a track
press the corresponding keypad button.
0 9
press the corresponding keypad button.
...
0 9 For tracks greater than 9, enter the digits
...
For tracks greater than 9, enter the digits
in sequence. For example, to play track 15,
in sequence. For example, to play track 15,
press 1 , then press 5 .
press 1 , then press 5 .
Cycles through the front panel display's
Cycles through the front panel display's DISP
brightness options
DISP
brightness options
Changes the available display modes on the
Changes the available display modes on the
MODE
MODE BD player
CD player
)
Fast rewind
)
Fast rewind
(
Fast forward
( Fast forward
Skip back to the start of the current/
]
Skip back to the start of the current/
] previous track
previous track
[
Skip forwards to the start of the next track
[
Skip forwards to the start of the next track
#
Stop playback
#
Stop playback
$
Play
$
Play
&
Toggles pause of playback
&
Toggles pause of playback
Changes audio decode format (Dolby
AUDIO
Enter a track in a programmed track list Digital, DTS, etc.).
MENU
Activates BD player menu.
Navigates track listings if supported by the MENU
player
Navigates track listings if supported by the
player
O selects the currently highlighted track if
supported by the player
O selects the currently highlighted track if
Toggles random ('shuffle') play on and off supported by the player
SHUFF
Returns navigation to the top level of the
Repeat track will cause the current track
.
menu ('Home').
to be played once the end of that track has
been reached. When navigating a menu, press this key to
RTN
return to the previous screen or selection
Repeat all will repeat the current section
of tracks once the end of the final track has Toggles random ('shuffle') play on and off
RPT SHUFF
been removed.
Repeat playback of the disc or pre-
To repeat a particular track, select that programmed selection of tracks. To repeat a
RPT
track and press twice. To cancel, press particular track, select that track and press
RPT
a third time RPT twice. To cancel, press RPT a third time.
RPT
Toggles between selecting the HD and CD Toggles between selecting the HD and CD
SACD
SACD
layer of SACD disc layer of SACD disc
E-10
The Settings menu allows you to configure all aspects
of your CDS27. This section will go through the menu
items and explain their function.
The only way to view the Settings menu is on the
settings
CDS27 display screen.
menus
Entering the settings menu
If the home menu is not currently displayed, press
on the remote control to display it.
MENU
Press C until the SETTINGS MENU item is displayed
and and press to enter.
OK
Navigating the menus
The CDS27 menus can be navigated by using the cursor
(arrow) keys on the remote control.
1. Use the B and C keys to navigate up and
down the current menu.
2. With the main section you require displayed,
press to select it.
OK
3. Use the and keys to navigate up and
B C
down the options.
4. Pressing selects a setting: use the and
E B
keys to change the setting.
5. Press OK to confirm the setting. Go back to step 4
to adjust any other settings in the current section.
<
6. Press to return to the previous screen if you
want to select another section to adjust.
Network Standby – This item determines whether Firmware Update – You can check for an upgrade to
network features are available when the CDS27 is in your player's firmware by selecting this menu item and
standby. pressing to highlight 'Network' , then press
OK
Selecting "ACTIVE" will maintain the network A message appears if no new firmware is available,
connection (required for IP control). otherwise follow the on-screen instructions.
Selecting "STANDBY" willl allow the network Load Defaults – Press with this item highlighted to
OK
hardware to be powered down in order to reduce power reset all settings to factory defaults.
consumption.
You are asked to confirm that you want to load the
Network Setup– This item allows the user to configure factory default settings. Select "cancel" to exit or
the unit to join an existing network, required for highlight the "yes" option and OK to confirm.
C
network audio playback and over the internet software
System Information – Use the
updates.
browses through options.
Auto Standby – Allows user to specifiy the period of
The System Information panel shows information
inactivity after which the unit will automatically enter
about your player, such as the IP address and firmware
standby. The options are: 5/10/15/20/25/30 Minutes.
version.
Disc Auto Playback – controls whether an optical disc
Network Audio - Allows the user to enable or disable
(e.g. CD) will play automatically after it is inserted.
the UPNP rendering capability of the player. Setting
On: Optical discs will play automatically.
< this option to 'off ' will disable network audio.
Off: play must be pressed to play a disc.
<
Digital Output - Allows the user to limit the sample rate
of the coax/optical digital output.
E-11
again.
OK
'
to
' ,
/ cursor keys to