Operation - Honeywell 015640 Montage, Anschluss, Anleitung

8
12. Start-up
12.1 Check installation
To ensure reliable functioning, all system parts must be installed correctly.
12.2 Insert battery and close housing
After installing the battery and connecting the battery connector plug, the detector
performs initialization. Both LEDs are flashing (see 13.1.4). After flashing, the detector
is ready for operation. If necessary set up the operating mode (see Chapter 11).
12.3 Walk test (Test of the function)
Perform a walk test for every detector
panel). The walk test can be switched on and off directly via the control panel.
Check the range of the detector. To do so, open or close the window / door under
realistic conditions. Each release can be seen at the led of the detector.
12.4 Insert seal
(see Chapter 4).
Ensure that the housing is closed correctly.
Insert the seal. The housing is now locked and can only be opened by removing the seal.

13. Operation

13.1 LED indication
13.1.1 After disarming
Note: A detected alarm remains stored in the detector until it is cleared.
The red LED flashes quick:
First alarm
This detector was the first to trigger an alarm.
The red LED flashes slowly:
Subsequent alarm
All subsequent detectors.
13.1.2 Operating state "walk test"
The red LED flashes slowly:
Triggering detected at least at an input.
The yellow LED flashes slowly:
This signifies that a battery fault
has occurred.
13.1.3 Operating state "armed" and "disarmed"
The LED indication is blanked.
13.1.4 Special case initial start up
The red and yellow LEDs are flashing quick (in the intervall)
After applying the operating voltage (battery) only in the case of initial start
up.
14. Accessories
082404 Magnet in surface mounted housing, traffic white
082414 Magnet in surface mounted housing, brown
082424 Magnet in surface mounted housing, gray
incl. 1 spacer-kit
Dimensions (W x H x D) 55 x 14 x 13 mm
Height of spacer 1x 10 mm, 1x 5 mm, 1x 2 mm
082405 Magnet in s.m. housing and spacer-kit, traffic white
082415 Magnet in s.m. housing and spacer-kit, brown
082425 Magnet in s.m. housing and spacer-kit, gray
incl. 3 spacer-kits
Dimensions (W x H x D) 55 x 14 x 13 mm
Height of spacer 3x 10 mm, 3x 5 mm, 3x 2 mm
015606 Lithium battery for RF magnet contact
Lithium battery including connecting cable 3,6 V
Honeywell Commercial Security
Novar GmbH
Johannes-Mauthe-Straße 14
D-72458 Albstadt
www.honeywell.com/security/de
(see installation instructions of the control
(low battery voltage)
:
Mounting and Connection Instructions RF magnet contact
15. Technical data
Operating voltage U_b
Battery lifetime
Frequency range 1
Transmission power 1
Frequency range 2
Transmission power 2
Transmitting range
Installation position
Conformity to guidelines
Protection class as per EN 60 529
Enviromental class as per VdS
Operating temperature range
Storage temperatur range
- without battery pack
- with battery pack
Dimensions (W x H x D)
Colour
*Battery lifetime depends on actuations per day:
typ. 2,7 years with 1000 actuations per day
typ. 2,5 years with 1000 actuations per day with connection
of external contacts.
Hereby, the Novar GmbH declares that the radio equipment RF
magnet contacts, Item no. 015640, 015642 and 015644 is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration can be downloaded from our homepage
https://www.security.honeywell.de/ in the service/download area.
16. Cleaning and care
The housing can be cleaned when necessary with a soft cloth.
Use a cloth moistened slightly with water if heavily soiled.
Do not use cleaning agents, abrasives or solvents such as spirits,
alcohol or petrol!
17. Warnings about lithium batteries
The device contains a lithium battery. To avoid the risk of fire or burns, the battery must
not be damaged, short-circuited or reloaded. Do not contact it with fire or water. There is a
risk of explosion if the battery is changed improperly. Replace the battery only by the
same or an equivalent type recommended by the manufacturer. Dispose used batteries
according to EU guideline 2006/66/EG (see following text).
A battery change must only be carried out by qualified personell introduced to the
VDE regulations.
Notes on environment / disposal
Batteries and recharchable batteries - even free from heavy metal - must not
disposed of in domestic waste. According to EU guideline 2006/66/EG users are
obligated to return batteries for recycling. In Germany they will be accepted for free
at each selling point; alternatively they can be dispensed in public storage vessels
for old batteries or at public waste disposal authorities.
Outside of Germany please observe the local regulations on battery disposal.
Commercial batteries may contain heavy metal labelled by:
Pb for lead
Cd for cadmium
Hg for mercury
18. Approvals
VdS approval no.
Approved as radio connection module for magnetic contacts.
P02650-10-002-06
2017-06-28
© 2017 Novar GmbH
1 battery pack 3,6 V/2,45 Ah
typ. 2,8 years*
433,05...434,79 MHz
<10 mW
863...870 MHz
<25 mW
typ. 300 m by free visibility
any position
VdS approval Class B
IP 30
II
-10 °C to +55 °C
-25 °C to +70 °C
25 °C +/- 10 °C
220 x 24 x 33 mm
traffic white (similar to RAL 9016)
brown (similar to RAL 8017)
grey (similar to RAL 7012)
Pb Cd Hg
G115509