Turning On The Appliance - Scholtes lvx 12-56 Anleitung

Turning on the Appliance

How to start a wash cycle
Insert the plug into the electricity socket to power the
dishwasher. Turn on the water tap completely and press ON-
OFF button "A"; the display lights up and the wash cycle
time selected on the knob will flash.
Starting and setting the cycle.
Turn the cycle selector "M" until the reference notch on the
knob corresponds with the symbol or number of the cycle
you wish to set (consult the wash cycle table contained in
this manual, especially when first using the appliance).
After a few seconds, a beep indicates the wash cycle has
started and indicator "G" displays the symbol corresponding
to the phase with which it has begun. The counter "L" will
indicate the estimated amount of time left until the end of
the wash cycle.
Do not expect a precise countdown as the wash cycle starts
with an estimated cycle time that is updated as the cycle
progresses and according to a number of parameters that
affect the cycle itself (such as water hardness, the tempera-
ture of the water, the degree of soil, etc.).
You want to wash on one rack only? Remember to use
half the amount of detergent.
If you only have a few dishes to wash, you can load these
onto one rack only, saving on both water and electricity.
Press button "I", a beep will sound and indicator "N" appears
on the display. Each time you press the button, a beep will
sound and symbol corresponding to the upper rack or
symbol corresponding to the lower rack will appear. If
you press the button once more, the selection will be reset
and the dishwasher will consequently wash on both racks.
To use the racks correctly, we recommend you read the
chapter entitled "Loading the dishes".
Cycle phase under way indicator
Your dishwasher is equipped with an indicator "G" comprising
4 symbols which represent the different phases of a wash
cycle. When the wash cycle has started, the display will indi-
cate the phases under way in sequence.
These phases are:
pre-wash wash
Cancelling and modifying a wash cycle in progress
Premise: a wash cycle in progress can only be modified if it
hasn't been running for long.
To modify it, turn the knob and set it to RESET. After a few
seconds, you will hear 4 beeps, indicator "G" relating to the
phase under way will turn off and 3 dashes will appear. At
this point, all the settings will have been cancelled.
rinses drying
To select a new wash cycle, repeat the instructions contained
in the paragraph entitled "Starting and setting the cycle".
You've left out a dish?
You can interrupt a wash cycle by pressing the "ON-OFF"
button, then place the forgotten dishes into the appliance,
which will start up from where it was interrupted when you
turn it back on.
There's been a power failure? Have you opened the
dishwasher door?
The wash cycle stops and then restarts when the electricity
comes back on or when you shut the door.
How to programme extra drying.
If you want your dishes to be perfectly dry, follow the
instructions below.
Set the knob to RESET and make any specific settings, such
as:
- upper or lower rack
- delayed start
Start the wash cycle by turning the knob and open the
appliance door. Observe symbol
for about 4 seconds, while the word "OFF" appears on the
display (extra drying disabled).
If you press button "I" immediately, you will hear a prolonged
beep and the word "ON" will appear on the display: the
extra drying has been enabled.
Once you have made your selection, shut the appliance door;
a beep will sound and the wash cycle will either start
immediately or after the delay, wherever set.
Remember that with extra drying, the wash cycle will last
longer, to provide you with drier dishes.
At the end of the wash cycle
At the end of the wash cycle, 2 beeps are sounded and the
word END flashes. Bring the selector back to the RESET
position, and the 3 dashes for programming cancellation will
appear.
Warning:
Turn the display off by pressing button "A", unplug the
appliance from the electricity socket to cut off the power
supply; the power supply cable should consequently be
easily accessible.
Turn off the water tap and open the door.
Wait a few minutes before removing the dishes: this way
you won't have to handle them while they're still hot and
they will dry better.
Empty the bottom rack first.
Make sure the wash cycle has ended before removing the
dishes!
17
for drying: it will flash
GB