Herunterladen Inhalt Inhalt Diese Seite drucken

Inhaltsverzeichnis - Cooper Power Tools GARDNER-DENVER 140PH45Q Betriebsanleitung

Inhaltsverzeichnis

Werbung

140/160PH
D D
Diese Betriebsanleitung vor dem Auspacken
und vor Inbetriebnahme des Werkzeugs lesen
und genau beachten! Der Schrauber darf nur
von Personen benutzt, gewartet und instand-
gesetzt werden, die mit den Sicherheitshin-
weisen und der Betriebsanleitung vertraut sind.
Die örtlichen Sicherheitsvorschriften bezüg-
lich Installation, Betrieb und Wartung sind stets
zu befolgen.
S
ICHERHEIT
Nehmen Sie den Schrauber erst in Betrieb,
wenn Sie die Sicherheitshinweise und Bedie-
nungsanleitungen gelesen und voll verstanden
haben.
S
YMBOLE
Warnung!
Dieses Zeichen warnt vor einer
möglicherweise gefährlichen Si-
tuation . Wird diese Warnung
nicht beachtet, können schwer-
ste Verletzungen auftreten.
Achtung!
Achtung!
Dieses Zeichen bezeichnet eine
möglicherweise schädliche Si-
tuation . Wird dieser Hinweis nicht
beachtet, können das Produkt
oder Teile davon beschädigt wer-
den.
Hinweis!
Die Zahl im Quadrat ist ein Ser-
vice-Hinweis. Hier werden zusätz-
liche Informationen für die richti-
ge Demontage und Montage
gegeben.Die Hinweise werden
unter 10. Hinweise erklärt.

Inhaltsverzeichnis

1.
2.
3.
4.
5.
6.
6.1
6.2
6.3
6.4
6.5
6.6
7.
+ Ersatzteil-Bestelliste
8.
Montagehinweise
9.
Vorrichtungs-Bestelliste
10.
Hinweise
Read and carefully observe these operating
instructions before unpacking and operating
the tool! The tool must be operated, maintained
and repaired exclusively by persons familiar
with the operating instructions. Local safety
regulations regarding installation, operation and
maintenance must be followed.
S
AFETY
Only operate this tool after safety instructions
and this service manual are fully understood.
S
YMBOLS
Warning!
This symbol identifies the poten-
tial for a hazardous situation.
If this warning is not followed, a
serious injury could occur.
Caution!
Caution!
This symbol identifies the poten-
tial for a damaging situation. If
a caution note is not followed, the
product or parts of the product
could be damaged.
Note!
The number in a square indicates
a service note. Additional infor-
mation is provided for disassem-
bly and assembly in section 10.
Contents
5
1.
Technische Daten
6
2.
Product Description
6
3.
Torque Adjustment
6
4.
Inspection and Maintenance
6
5.
6
6.
Repair Instructions
6
6.1
Removing the Power Unit
6
6.2
Dismounting the Pulse Unit
7
6.3
Assembly of the Pulse Unit
6.4
7
6.5
Motor Assembly
7
6.6
Trigger Valve Disassembly
7.
16-21
+ Spare Parts List
22
8.
25
9.
Fixtures order list
26
10.
Notes
P1643E 11/98
GB
GB
Lisez et observez ce manuel d'instructions avant
déballage et mise en marche de l'outil. Cet outil
ne doit être utilisé, entretenu et réparé que par du
personnel qui est familier avec ces instructions
de service. Les consignes de sécurité en vigueur
dans le pays de l'utilisateur doivent être
obligatoirement respectées par toute personne
chargée de l'installation, le fonctionnement et la
maintenance de l'outil.
S
Lire d'abord attentivement les consignes de
sécurité et le mode d'emploi spécifique à ce type
d'outil et uniquement faire fonctionner l'outil
lorsque son utilisation a été parfaitement
comprise.
S
Attention!
Contenu
5
1.
8
2.
8
3.
8
4.
8
5.
8
6.
8
6.1
8
9
6.2
9
6.3
9
6.4
9
6.5
16-21
6.6
22
25
7.
26
8.
9.
10.
F F
ÉCURITÉ
YMBOLES
Signal de danger!
Ce signe vous met en garde contie
une situation dangereuse.
Des blessures graves peuvent
s'en suivre, si cet avertissement
n'est pas respecté.
Attention!
Ce signe qualifie une situation
pouvant
potentiellement
provoquer un endommagement.
Le produit ou ses composants
peuvent être détériorés, si les
consignes
ne
respectées.
Annotations
Le chiffre encadré indique une
annotation de service. Ici on vous
donne
de
plus
informations sur le montage et le
démontage
correct.
annotations sont expliquées dans
chapitre 10.
Données techniques
Description produit
Réglage du couple
Contrôle et maintenance
Que faire lorsque ...
Instructions de réparation
Démontage du mécanisme
d'entraînement
Démontage de l'unité d'impulsion
Montage de l'unité d'impulsions
Remplissage d'huile au moyen du
dispositif <A>
Montage du moteur
Démontage des soupapes
de fermeture
Vue éclatée
+ Liste de pièces de rechange
Instructions de montage
Liste de commande des dispositifs
Remarques
sont
pas
amples
Ces
5
10
10
10
10
10
10
10
11
11
11
11
16-21
22
25
26
3

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Gardner-denver 160ph456

Inhaltsverzeichnis