OKBABY Eggy Bedienungsanleitung Seite 8

Illustration 7:
Adjust the vertical and horizontal position of the child seat accord-
ing to parameters seen in the figure. The barycentre (see fig. red
circle) must not be more than 10 cm behind the wheel axis. If nec-
essary, correct the horizontal position of the child seat as described
in illustration 8. When the seat is correctly in place, tighten the
screws (8) slowly and evenly until the fastening block stops rotating
around the frame. The optimum torque wrench setting is 8 Nm.
Illustration 8:
Correcting horizontal position.
Phase 1 : Press the two halves of the locking pin handle together so
that the safety clip opens.
Phase 2 : Turn the locking pin 90° downwards.
Phase 3 : Move the child seat horizontally until you find the right
position.
Phase 4 : Fix the support as shown in illustration 5.
Illustration 9:
Fastening the footrests: Place the footrest marked "SX" in the high-
est position of the seat's left leg. Insert the adjusting pin marked
"SX" from the outside of the child seat inwards. Repeat the opera-
tions for the right footrest and relative adjusting pin, marked "DX".
Using the seat:
Illustration 10:
Only for Eggy Relax: Inclining the child seat. To set the inclination
of the child seat, pull the release knob (E) upwards. Hold the release
knob upwards, and with your other hand incline the seat to the
desired position. Then let go of the release knob (E).
Illustrations 11-12:
Adjusting the footrest height. Rotate the adjusting pin upwards and
move the footrest to the desired position. Once in the desired posi-
tion, block the footrest by rotating the adjusting pin downwards.
Illustration 13:
Fastening the child's safety belt: Adjust the height and length of the
belts according to the size of the child. Setting belt height: the belt
can be extracted to adjust its height by inserting the buckle behind
the backrest through the opening each time. Choose the upper or
lower openings to fix the belts based on the child's height. Setting
belt length: modify belt length by sliding the buckles. The belts
must be fastened firmly without them being too tight for the child.
Fastening the belts: Fasten the belt clasp. Check that the belt clasp
10 Rear child's seat Eggy / Eggy Relax
clicks shut properly, and then pull the belt.
Illustration 14:
To unfasten the belt, simultaneously press the two buttons (front
and rear) found on the clasp. The clasp will open.
Illustration 15:
Fastening and unfastening the child's feet: to secure the child's feet,
secure the strap on the external side of the foot in the clasp on the
rest.
Always make sure your child's feet are well fastened to the foot-
rests. The foot strap is long for easy adjustment.
Illustration 16:
Removing the child seat. Press the release button on the fasten-
ing block (7) and remove the child seat. To hook the seat on again,
insert the support arm (5) in the two fixing block holes (7) until the
lever clicks (fig.6).
NOTE: the fastening block (7) is fitted with an anti-theft system
actuated using one of the keys (11) supplied (Fig. 17). Insert the
key (11) in the fastening block (7) and rotate in an anti-clockwise
direction to lock the release button to prevent the seat from being
removed. Rotate the key (11) in a clockwise direction to restore
operation of the release button.
Maintenance
1) Clean the seat, the padding and the belts with warm water and
a mild detergent. Do not use solvents or abrasive or corrosive
detergents. Leave the padding to dry in the open air out.
2) Seat repairs and replacement of damaged components must
only be carried out by authorized personnel.
Technical specifications
Product Child bike seat OKBABY
mod. Eggy / Eggy Relax
Dimensions 40x34x80 cm (LxDxH)
Weight 4.4 kg
Rear child's seat Eggy / Eggy Relax 11