Neumann Mission Programmieranleitung/Regelungsanweisungen Seite 7

Mission
Mowing area is too big.
Blades are dull.
Grass is being cut
The cutting height is set too low for the length of
unevenly.
the grass.
Grass or other object has wrapped around the
blade disc.
There is a build-up of grass in the Blade Disc or
Motor Frame Box.
The LED light on the
Charging base does not There is no power.
turn on.
Green light flashing on
The Boundary Wire isn't connected.
charging base.
®
Your Mission is inside its
territory but the display
says "outside working The boundary wire ends are clamped incorrectly. Reverse the boundary wire ends.
area" and the LED is
green.
Poor connection caused by debris on the
Charging Strip.
The charging time is far
more than 2h.
The charging protection program has activated
due to high temperature.
There is no power.
The mower does not
charge.
Does not operate correctly while manually
charging.
Something is clogged in the Blade Disc.
®
Mission is starting to have
shorter run-times between
Mission
charges.
The battery may be exhausted or old.
The clock is not set to the correct time.
®
Mission is not operating
Programmed cutting times for Mission
at the correct time.
correct.
Environmental influences.
®
Mission cannot correctly
dock with the Charging
Poor connection caused by debris on the
Base.
Charging Strip.
The Green light on the
Charging Base turns The charging base is overheating, the LCD will
ON before charging is display "Over temperature".
complete.
The boundary wire of another Mission
another branded robotic mower is positioned too
closely.
® The boundary wire has been installed with tight
Mission runs outside the
® corners.
boundary wire. Mission
does not mow an area
In wet conditions, the boundary wire electric
within a boundary wire
signal may leak were wire has been joined or
®
zone. Mission reverses or
repaired.
rotates erratically near the
boundary wire.
There is boundary wire electric signal leakage
due to broken insulation.
The cutting area is larger than the allowable
cutting area for Mission
Foreign obstacles, such as twigs and branches
®
Mission wheels skid or
may be lodged under Mission
damage lawn.
The lawn is too wet.
®
Mission exits the
boundary wire due to high The Boundary Wire is placed on a slope steeper
speed when going down a than 25%(15°).
hill.
®
does not work enough hours per day.
®
is shaking heavily.
®
.
®
.
Add more hours to the mowing time.
Try decreasing the size of the mowing area or adding
more hours to the mowing time.
Change all the Blades and screws in order to balance
the Blade Disc.
Raise the cutting height and then gradually lower.
Check the Blade Disc and remove the grass or other
object.
Make sure the Blade Disc rotates easily. If needed,
you may take off the Blade Disc and then remove the
debris. See How to Clean.
Check the power cord is connected properly to the
charger and the charger is connected to a suitable
power supply.
Check the boundary wire has been connected
correctly to the charging base. Check there are no
breaks in the boundary wire.
Clean the Contact Pins located on the Charging Base
and the Charging Strip on Mission
Place the charging base in a shady area or wait until
the temperature has cooled down.
Check the power cord is connected properly to the
charger and the charger is connected to a suitable
power supply.
Refer to manual charging in Owner's manual.
Take off the Blade Disc and clean it.
The grass is too high and too thick.
Check the blade disc and blades, remove debris and
foreign objects from the blades and blade disc.
Replace battery.
Set the clock to the correct time.
®
are not Change the time settings for the mower to start and
stop.
®
Restart Mission
Clean the Contact Pins located on the Charging Base
and the Charging Strip on Mission
Place the charging base in a shady area or wait until
the temperature has cooled down.
®
or
Ensure your Mission
of spacing between the neighboring boundary wire.
Check the boundary wire to ensure the corners are
smooth.
Check boundary wire joints. Insulate to provide a fully
waterproof connection.
Repair damaged boundary wire insulation with
insulation tape.
Contact service agent.
Remove foreign objects from underside of Mission
Wait until lawn has dried.
Reposition the Boundary Wire away from slopes that
are steeper than 25%(15°). Please refer installation
manual for details.
®
using a cloth.
.
®
using a cloth
®
Boundary Wire has at least 2 m
7
EN
®
.