Neumann Mission Programmieranleitung/Regelungsanweisungen Seite 6

Notes
•
If the above error messages appear on the display, correct the problems first, then press "O" to
6
reset.
• Before turning power on, always check Mission
EN
displayed. This message is displayed also when Mission
• If for any reason—i.e. a party, children playing...—you want to park your Mission
with the home symbol
scheduled mowing session. If you want to re-start it, press STOP button, then press
• If an error repeatedly occurs in the same area of your lawn, you might have a problem with the boundary wire so
please refer to the previous installation instructions and check your set up with its help.
• If your lawn is divided in two separated areas, connected by a corridor less than 1m, one of which is not provided with
the charging base: when Mission
key with the home symbol and the charge process will start.
• If Mission runs abnormally once in a while, please try to restart it. If the problem cannot be solved, please contact
®
Neumann Service Agent for help.
• Do not wash the machine with a high pressure washer. This could cause damage to the battery or the machine.
• Your Mission software can be updated when new versions become available. The software version will be displayed
®
in the diagnosis page by pressing button 2 on homepage. The latest software can be downloaded from our website
www.neumannrobotics.com. See the detailed guideline on download page. The manual supplied in the box is based
on the default software in the mass production. Some new features/functions in the new version may not exist in
the manual. If you find some settings that are not detailed in the manual, please visit www.neumannrobotics.com to
download the latest manual.
Fault symptoms
®
If your Mission does not work correctly, follow the trouble shooting guide below. If the fault persists, contact your dealer.
Refer to the Owner's Manual for Mission
Symptom
®
Mission turns on, but the
Blade Disc does not move.
®
Mission vibrates.
1. Turn power off.
2. Take Mission to a lawn area free from obstacles.
®
3. Turn power on.
4. If the error message is still displayed; turn power off; turn Mission
there's any debris causing a blockage in the top cover.
5. Remove any possible obstruction, turn the Mission
1. Turn power off.
2. Take Mission to a lawn area clear of obstacles, turn power on.
®
3. If the error message is still displayed: turn power off, turn Mission
there's nothing lifted up.
4. Remove any possible object, turn Mission
1. Turn Mission upright.
®
2. If still not work,
Firstly, position the mower on a horizontal surface.
Press Key "2" to enter the diagnosis interface, and press
Key "5" for a few seconds until the three numbers 1 2 & 3
highlighted below turn back to zero. (See fig. A)
1. The contact between the Charging and Contact Pins may be obstructed in some way.
2. Wipe off the Charging and Contact Pins, making sure there is not an object obstructing
them, then place your Mission
connection.
1. This means that there is low battery voltage.
2. In this case you must turn Mission
be shown on screen, which means it starts charging.
®
. Mission will go to its base and stay there. Please note Mission
®
runs out of charge, take it manually to the charging base, turn power on, press the
®
®
component information.
Cause
®
Mission is searching for the Charging Base
(except that you press the HOME button to
make it go to the charging base, or the "Enable
boundary cut" function is operating).
Blades may be damaged. Check condition of the
Blade Disc.
upright, turn power on.
®
in the charging base and check that the Pins make good
®
off and place it in the Charging Base, then "charging" will
®
is inside its territory. If not, the message "outside working area" will be
is sitting over the boundary wire when turned on.
®
This is normal, Mission
Disc does not rotate while it is searching for the
Charging Base automatically.
Check the Blades, and replace them if damaged .
Remove debris and foreign objects from the blades
and blade disc.
upside-down and check if
®
upright, turn power on.
®
upside-down and check
®
A A A
1 1 1
2 2 2
3 3 3
in the charging base: press the key
®
will now wait until the next
®
button to start your Mission
Action
®
needs to recharge, the Blade
.
®