Installation Instructions; Operation - Halemeier S-Mitter MultiColor Bedienungsanleitung

S-Mitter MultiColor

Installation Instructions

en

Operation

Programming the RGB system
The distance between radio transmitter and receiver should not exceed 0.5 m.
5 different handheld transmitters can be learned on a receiver.
How to learn the transmitter:
1. Install and establish power supply.
2. Briefly press programming button of the receiver (approx. 1 second) until the red LED lights up.
3. Briefly press 1x the (On/Off) master button on the handheld transmitter.
4. After approx. 10 seconds the programming process is automatically terminated - LED off.
How to clear a learned transmitter - delete entire transmitter memory
1. Press and hold programming button. The LED will begin to flash.
2. Continue to hold programming button until the LED stops flashing.
3. After releasing the button, all transmitters will be deleted.
Note
The S-Mitter receiver and its aerial must not be positioned at a
distance of less than 50 cm from electronic transformers/ballasts,
including their leads.
Other electricalloads (e.g., microwave ovens, hi-fi and TV systems)
must be at least 50 cm away. Installation on or behind metal parts,
mirrors or foil-covered surfaces is not permissible.
Operation
Start / Stop of the
automatic colour cycle
press briefly
Dimming
overall system.
Duration of dimming
light / dark max. 5 sec .
Radio transmission
A non-exclusive transmission path is used for radio transmission, errors can therefore not be ruled out. The radio system is intended for use in the living room.
The transmission range of a handheld transmitter is up to 30m in a free field.
To facilitate future programming of the receiver, it is advantageous to mount it in an easily accessible place.
Hazards and disposal instructions
The device is intended only for switching and dimming RGB lighting. Observe the maximum load of the connected load / electronic ballast and receiver
(see technical data). Keep batteries out of reach of children. If batteries are swallowed, call a physician immediately. Do not reverse polarity of the batteries and
observe the [+] and [-] marks on the battery and transmitter. The device is supplied with a standard battery (2 x AAA) that must not be charged.
A charging of these batteries can cause injury and damage by exploding or leaking. Observe all safety instructions printed on the battery.
Never open the battery or throw the battery or device into a fire.
Keep installation instructions in a safe place!
Please keep these installation instructions after installing the product so that any later changes can be carried out in the proper manner.
m
A disposal on domestic waste is not permitted!
A disposal must be according the public requirements of waste disposal/recyclin
c3M Mq
Transmission control LED
}
Rocker keys (+) & (-) are used
for manual mixing of each colour
press and hold max. 5 sec. (+ / -)
}
Configure 1-4 memory slots for personal colour setting
setting / override by pressing and holding (approx. 3 sec) the desired button
Halemeier GmbH & Co.KG - Lange Straße 51 - D 49326 Melle Neuenkirchen
m
Programming key
Technical Data:
Receiver
24VDC / 12VDC
Rated voltage:
24VDC max.72W (1x) / 12VDC max.36W (1x)
switching capacity:
Type of load: Dimmable LED RGB (MC) lights
Number of handheld
transmitters: max. 5
Reception frequency: 433,9 MHz
Optional: Capacity expansion only with Repeater
Master key for full switching on
and off of all channels.
Last switching state is stored.
briefly press - On / Off
Change the speed of the colour
cycle (approx. 0.5 to 15 minutes)
by pressing the rocker switch.
(+) slower
(-) fast
Technical Data:
Radio handheld transmitter
Voltage supply:
Batteries:
Transmission frequency:
Dimensions:
g.
3 VDC
2x 1,5V AAA
433,9 MHz
184 x 28 x 21mm
19.948.17 / 19.05.2015