Verwandte Anleitungen für Barloworld Scientific Techne HB-1D
Inhaltszusammenfassung für Barloworld Scientific Techne HB-1D
- Seite 1 HB-1D Hybridiser Operator’s Manual Issue 25 Date of issue: 3rd May 2005 Techne is a trademark © Techne, 2003...
-
Seite 3: Inhaltsverzeichnis
H B - 1 D O P E R A T O R ’ S M A N U A L CONTENTS HB-1D issue 20 onwards Operator's Manual page SAFETY AND INSTALLATION English Français Deutsch Español Italia INTRODUCTION Initial checks Specification Unpacking Installation... - Seite 4 H B - 1 D O P E R A T O R ’ S M A N U A L...
- Seite 5 H B - 1 D O P E R A T O R ’ S M A N U A L NOTES...
-
Seite 6: User Maintenance
Techne dealer or, 3. Plug the mains cable into the socket on the rear of the unit. Barloworld Scientific Ltd 4. Place the unit on a suitable bench or flat workspace, or in a Beacon Road, Stone... -
Seite 7: Après Utilisation
H B - 1 D O P E R A T O R ’ S M A N U A L Introduction Après utilisation Veuillez lire attentivement toutes les instructions de ce document Lorsque vous avez fini de chauffer les échantillons, avant d’utiliser l’appareil. -
Seite 8: Einleitung
H B - 1 D O P E R A T O R ’ S M A N U A L Garantie Einleitung Die Garantiedauer des Gerätes ist auf der beiliegenden Bitte lesen Sie diese Bedienungsanleitung komplett bevor Sie Garantiekarte angegeben und schließt Fehler im Material oder dieses Gerät benutzen. -
Seite 9: Español
H B - 1 D O P E R A T O R ’ S M A N U A L Introducción Garantía Le rogamos lea cuidadosamente la información contenida en Este aparato está garantizado contra cualquier defecto material este folleto antes de manipular el aparato. o de fabricación durante el periodo especificado en la tarjeta de garantía adjunta. -
Seite 10: Per Informazioni Tecniche
Techne o, direttamente la l’apparecchiatura e l’utilizzatore. Barloworld Scientific Ltd Tenere presente che gli apparecchi riportanti sulla targhetta Beacon Road, Stone 230 V funzionano a 220V. Gli apparecchi riportanti 120V Staffordshire funzionano a 110V. Comunque, in entrambi i casi la velocità... -
Seite 11: Introduction
However, the chemical manufacturer's safety precautions must be used when using the HB-1D. The Techne HB-1D also incorporates the following features: a) a temperature range of ambient +10 C to 100 b) it holds 1, 2, 3 or 4 x 80mm diameter hybridisation tubes. -
Seite 12: Specification
H B - 1 D O P E R A T O R ’ S M A N U A L Specification Maximum Number of Hybridisation Tubes 6 (large and small) 24 mini tubes Temperature Range # ambient +10° to 100°C (NOTE: minimum temperature must be greater than 10°C above ambient) Rotation of Hybridisation Tubes 5 rpm to 20rpm and off... -
Seite 13: Unpacking
H B - 1 D O P E R A T O R ’ S M A N U A L Unpacking Ensure that the following have been removed from the packing: • The Hybridiser. • Drip Tray (not Techne Inc). • Power Lead. - Seite 14 H B - 1 D O P E R A T O R ’ S M A N U A L SPEED CONTROL...
-
Seite 15: Warning
H B - 1 D O P E R A T O R ’ S M A N U A L Warning THE UNIT WORKS UP TO 100°C. This temperature can cause burns. Techne take great efforts to protect operators from hazards, but the following points are brought to your attention: Use care and wear protective gloves to remove hybridisation tubes from the cabinet if the unit is at high temperature. -
Seite 16: Switching On
H B - 1 D O P E R A T O R ’ S M A N U A L Switching On Once your HB-1D is connected to a power supply, switch it on using the power switch next to the power inlet socket on the rear panel. -
Seite 17: Operation
H B - 1 D O P E R A T O R ’ S M A N U A L OPERATION The Tubes The Hybridisation Tubes must be checked regularly and replaced if any damage occurs. Any damage to the ends of the tubes can cause them to break when the end caps are inserted. - Seite 18 H B - 1 D O P E R A T O R ’ S M A N U A L Small Tube (3 x 44mm dia) assembly Unscrew the tube end cap. Place the filters in the tube and replace the end cap.
-
Seite 19: The Hb-1D
H B - 1 D O P E R A T O R ’ S M A N U A L The HB-1D Insert the tubes or tube holder into the HB-1D ensuring that they rotate freely and engage on the drive rollers. Close the door. -
Seite 20: The Front Panel Controls
H B - 1 D O P E R A T O R ’ S M A N U A L The Front Panel Controls The front panel controls consist of three buttons for controlling the display, a four digit LED display and three indicators. The SET temperature Button TEMPERATURE ∇... -
Seite 21: Power Indicator
H B - 1 D O P E R A T O R ’ S M A N U A L Tube temperature NOTE: It takes approximately 50 minutes for the interior of the hybridisation tubes to reach the displayed temperature depending upon the number of filters and amount of hybridisation fluid used. -
Seite 22: Basic Protocol For Southern Hybridisations
H B - 1 D O P E R A T O R ’ S M A N U A L BASIC PROTOCOL FOR SOUTHERN HYBRIDISATIONS * INSERTION OF FILTERS Place a wet or moist filter, DNA side facing inwards, into a hybridisation tube and allow it to adhere to the glass. -
Seite 23: Technical Information
H B - 1 D O P E R A T O R ’ S M A N U A L TECHNICAL INFORMATION Brief fault finding notes are given in this section. NOTE THAT THIS EQUIPMENT SHOULD ONLY BE DISMANTLED BY PROPERLY TRAINED PERSONNEL. -
Seite 24: If An Incorrect Message Is Displayed
H B - 1 D O P E R A T O R ’ S M A N U A L Cleaning your HB-1D Before cleaning your unit ALWAYS disconnect from the power supply and allow to cool. You can clean the case of the HB-1D with a cloth dampened in soapy water or ethanol. -
Seite 25: Accessories And Spares
H B - 1 D O P E R A T O R ’ S M A N U A L Accessories and Spares The following may be purchased from Techne or their dealers. All Techne tubes are made from Borosilicate glass These tubes are the preferred tubes: FHB12 80mm external diameter hybridisation tube assembly... - Seite 26 H B - 1 D O P E R A T O R ’ S M A N U A L...