Werbung
Verfügbare Sprachen
Verfügbare Sprachen
"Keep warm" function (5)
•
Press the button (5) « » to switch on the
"keep warm" function, the illumination of this
button and water level scale will switch on.
•
Display will indicate the current temperature
and the temperature, set at the moment of
pressing the button (5) « » (recorded into
the unit memory at the moment of pressing
the button (5) « »).
•
Water temperature will be kept at the preset
level during 30 minutes.
Note: If you select the mode of water heating to
a 20 degrees, the water temperature will even-
tually reach the room temperature, if the room
temperature is above 20 degrees. In this case
this mode will not operate.
"Clean water" function
•
Press the button (8) to switch on the "clean
water" function, the illumination of this button
and water level scale will switch on.
•
The kettle will bring water to the boiling tem-
perature and keep it boiling during 3 minutes.
•
The function of long boiling will reduce the
chlorine level in water and provides drink
purity.
•
Before removing the kettle from the base (12)
make sure that it is switched off.
•
After switching off the kettle wait for 15-30
seconds, then you can switch it on again for
water boiling.
•
If you accidentally switched on the kettle, but
the water level appeared to be below the min-
imal mark, the kettle switches off automati-
cally. In this case remove the kettle from the
base (12), let it cool down for 5-10 minutes,
then fill it with water and switch on, the kettle
will operate in normal mode.
•
Be careful while opening the kettle lid, the
outgoing steam is very hot.
Heating to a preset temperature + boiling
(6+7)
+
Stepwise selection of water temperature is used:
20, 30, 40, 50, 60, 70, 80, 90°C.
•
Set the required water heating temperature
by pressing the button (6) consequently « ».
•
Press the button (7) « ».
•
Water will cool down to the preset tempera-
ture after boiling; once it reaches the pre-
set temperature you will hear a short sound
signal.
VT-1167 IM.indd 5
Note: If you fill the kettle with cold water, select
the mode of water heating to 20 degrees and
boil water, water will cool down to the room
temperature, if the room temperature is above
20 degrees.
Heating to a preset temperature + keep
warm (6+5) +
Stepwise selection of water temperature is
used: 20, 30, 40, 50, 60, 70, 80, 90°C.
•
Set the required water heating temperature
by pressing the button « » (6) consequently.
•
Press the button (5) « ».
•
Water will reach the preset temperature that
will be kept during 30 minutes.
Note: If you fill the kettle with cold water and
select the mode of water heating to 20 degrees
with keeping the temperature at such level,
the water temperature will eventually reach the
room temperature, if the room air temperature
is above 20 degrees. In this case this mode will
not operate.
Heating to a preset temperature + keep
warming + boiling (6+5+7) + +
Stepwise selection of water temperature is
used: 20, 30, 40, 50, 60, 70, 80, 90°C.
•
Set the required water heating temperature
by pressing the button « » (6) consequently.
•
Press the button (5) « ».
•
Press the button (7) « ».
•
Water will cool down to the preset tempera-
ture after boiling and the preset temperature
will be kept during 30 minutes.
Note: If you fill the kettle with cold water, select
the mode of water heating to 20 degrees and
keeping warm after boiling, water will cool down
only to the room temperature, if the room air
temperature is above 20 degrees.
Unique keep warm function (7+5) +
You can set any water temperature from 20°C up
to the boiling temperature.
1nd method (with preliminary water boiling)
•
Press the button (7) « ».
•
Once water reaches the required tempera-
ture, for instance, 36°C, press the button
(5) « ».
•
Switch off water boiling, by pressing the but-
ton (7) « ».
•
Water temperature will be kept at the preset
level during 30 minutes.
5
ENGLISH
04.04.2012 12:53:41
Werbung
