Vitek VT-1167 SR Betriebsanweisung Seite 4

ENGLISH
• Do not repair the unit by yourself. If you find
any damages, unplug the unit and apply to
the authorized service center.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY.
Before the first usage
•
Unpack the kettle.
• Make sure that operating voltage of the unit
corresponds to voltage of your mains.
Note: After unit transportation or storage at
low temperature it is necessary to keep it for
at least two hours at room temperature before
switching on.
•
Insert the power cord plug into the socket,
you will hear a sound signal and the display
(4) will switch on, water level scale (11) and
control buttons (5-8) illumination will flash,
and the current temperature inside the kettle
will be indicated on the display.
• To fill the kettle with water take it off the base
(12), open the lid (2) by pressing lid opening
button (3).
•
Fill the kettle with water till the max. mark on
the water level scale (11), close the lid, place
the kettle on the base (12). Make sure that the
lid (2) is closed tightly.
•
Switch on the kettle by pressing the (7) but-
ton, the button and water level scale illumina-
tion will switch on.
•
When water starts boiling, the kettle will
switch off automatically, you will hear 5 sound
signals, the water level scale illumination will
go out. Pour out water and repeat boiling pro-
cedure 2-3 times.
Note:
•
When using the kettle, make sure that the lid
(2) is closed tightly.
•
Before removing the kettle from the base
make sure that it is switched off.
Kettle usage
Avoid dropping or hitting of kettle, especially
when filling it with water.
Note: Cord storage (13) is on the reverse side
of the base (12). You can adjust the power cord
length, winding it over cord storage in corre-
sponding way.
•
Insert the power cord plug into the socket,
you will hear a sound signal and the display
(4) will switch on, water level scale (11) and
VT-1167 IM.indd 4
control buttons (5-8) illumination will flash,
and the current temperature inside the kettle
will be indicated on the display.
•
To fill the kettle with water take it off the base
(12), open the lid (2), by pressing the lid
opening button (3).
•
Place the filled kettle on the base (12) as
convenient for you, as it allows unit 360°
rotation.
• Switch on the kettle by pressing the (7) but-
ton, the button and water level scale (11) illu-
mination will switch on.
• The color of water level scale (11) illumina-
tion will change according to water tem-
perature.
Temperature °С
20°
30°
40°
50°
60°
70°
80°
90°
• When water starts boiling, the kettle will
switch off automatically, you will hear 5
sound signals, the water level scale illumina-
tion will go out.
"Heating to a preset temperature" function
(6)
This function allows to select required water
temperature for making different tea varieties.
•
Pressing the button " " (6) you can set the
required water heating temperature (20, 30,
40, 50, 60, 70, 80 or 90°С), the button and
water level scale illumination will switch on
• The current and preset temperature will be
indicated on the display.
•
When the preset temperature is reached,
you will hear a short sound signal, the con-
trol button and water level scale illumination
will go out.
Note: If you fill the kettle with cold water and
select the mode of water heating to 20 degrees,
the water temperature will eventually reach the
room temperature, if the room temperature is
above 20 degrees. In this case this mode will
not operate.
4
Color
Green
Green
Light blue
Light blue
Blue
Blue
Purple
Red
04.04.2012 12:53:40