Electrical Installation - JB Systems Light MICRO LED MANAGER Bedienungsanleitung

ENGLISH
Chase Yellow – Blue
Chase Red – Green
Chase Yellow – Green
Chase Cyan – Orange
Chase Green - Light purple
Chase Red – Yellow
Chase Gold Yellow - Blue

ELECTRICAL INSTALLATION

The electrical installation should be carried out by qualified personal only, according to the
regulations for electrical and mechanical safety in your country.
How to connect the LED-projectors to the output of the unit:
Important: Switch the Micro / Mini LED Manager OFF before you install the LED-projectors! The
maximum total load of the Micro Led Manager is 50W, spread over 3 colors: each of the 3 colors
has a max. load of 16W ~ 17W! The maximum total load of the Mini Led Manager Mk2 is 100W,
spread over 3 colors: each of the 3 colors has a max. load of 33W!
Two different types of passive LED projectors can be connected:
A. LED Projectors with a special 4pin connector (ex. LED STRIP):
Use the supplied conversion
cable and connect the
internal 4 wires to the
corresponding 4 terminals of
the MICRO / MINI LED
MANAGER. Fix all projectors properly and daisy chain the in/output cables until you reach the
maximum allowed load. Make sure to fasten the plastic ring of the connector.
B. LED Projectors with open wires (ex. LED GROUND LIGHT):
Simply connect the colored wires to the corresponding terminals on the LED MICRO MANAGER.
Make sure not to exceed the maximum allowed load:
 White wire: This is the common wire (anode)
 Red wire: This the power for the red LEDs.
 Green wire: This the power for the green LEDs Blue wire: This the power for the blue LEDs
Remark: the outputs to the LED-projectors are short circuits protected. However when a short circuit
occurred, it must be reset: disconnect the Micro / Mini LED Manager for about 10seconds from the mains
and plug it back in.
Connecting an external analog switch for blackout:
Using any ordinary on/off switch, you can put the output of the
Micro / Mini LED Manager in blackout, even if it's controlled
by DMX: for example you can use a regular "wall switch" to
turn the LED-light on/off at any moment!
 Connected wall switch in OFF position (contacts open):
output = ON
 Connected wall switch in ON position (contacts closed):
output = OFF (blackout)
JB SYSTEMS®
OPERATION MANUAL
Cyan
Blue
Deep Blue
Purple
Light Purple
Magenta
Pink
5/57 MICRO/MINI LED MANAGER Mk2
ENGLISH
Connecting the optional LED WALL DIMMER:
The LED WALL DIMMER is a small, easy to use, controller
that can be installed in any standard wall connection box. This
controller can be connected directly to the Micro / Mini LED
Manager. The 0V & +12V should be connected through a
normal 2wire cable. The DMX-signal should be connected
using a good quality balanced DMX-cable with good
shielding.
Remark 1: the Micro / Mini LED Manager should be set to
DMX-address 001, using the traditional DIP switches (see
"DMX addressing to learn how to do this)
Remark 2: if you want to control more than 1 (Micro) LED
manager, just connect the LED Managers together with the
DMX in/outputs and put all DMX addresses to 001.
Electrical installation in Master/slave-mode:
 You need to "daisy chain" the DMX in/outputs of 2 or
more units with a good quality balanced cable
 Switch the unit with the free DMX-input connector to master, the other units are automatically switched
as slaves. The DIP-switches on the slave units are disabled.
Electrical installation in Master/slave-mode with the LEDCON-02 remote:
 You need to "daisy chain" the DMX in/outputs of 1 or more units with the output of the LEDCON-02
remote using a good quality balanced cable
 The LEDCON-02 remote will be used to control all connected slaves. The Micro / Mini LED Managers
are automatically switched as slaves. The DIP-switches on the slave units are disabled.
Electrical installation in DMX-mode:
 The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
"daisy chain" your DMX controller and all the connected units with a good quality balanced cable
 To prevent strange behavior of the light effects, due to interferences, you must use
a 90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables, this
simply won't work!
JB SYSTEMS®
OPERATION MANUAL
6/57 MICRO/MINI LED MANAGER Mk2