Installing The Propeller - Atomik Whiplash 24 P1 RTR Bedienungsanleitung

INSTALLING THE PROPELLER

INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER INSTALLING THE PROPELLER
Slide the prop onto the drive shaft making sure to align the notch with the drive dog. Use the supplied lock nut to secure
the prop to the propshafts. Use caution when installing the prop as it may have extremely sharp edges.
aftermarket prop, make sure it is sized for a 3mm prop shaft. If you are not using a 3mm prop, you will need to shim the
prop shaft or use an adapter to increase the diameter to .118 inch.
INSTALLING THE HATCH
INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH INSTALLING THE HATCH
Secure the hatch by aligning it over the three magnets. The hull magnet pockets are designed so the hatch will easily
drop into place and the magnets key into place. A molded lip around the perimeter of the motor compartment is
designed so water will drain away from the compartment. For added water protection, use strips of clear tape to seal
the lid on all four sides.
1 8 000
1
6
If you are using a
2
ATOMIK-RC.COM