Troubleshooting; Spare Parts; Disposal; Ec Declaration - Rapid SIF-700 Betriebsanleitung

every year beside the indicated periodic maintenance. For this
purpose contact your supplier.
WARNING
Overdue maintenance can cause fire.
WARNING
Always fully disconnect the machine from the mains
before carrying out maintenance jobs as mentioned
below. First read the maintenance regulations at the
beginning of this manual.
The maintenance activities in the table below are strictly
reserved for well trained and authorised service engineers.
Component Action
Flexible adapters Check for airtightness and damages.
Replace if necessary.
Impellers Check for dirt. Clean if necessary.
7

TROUBLESHOOTING

If the product does not function (correctly), consult the checklist
below to see if you can remedy the error yourself. Should this
not be possible, contact your supplier.
WARNING!
After switching off the fan, wait at least 30 seconds
before opening the inspection cover.
Symptom Problem
Motor does not Fan does not
start. function.
Motor makes a Extraction
humming capacity
sound, but insufficient or
does not no extraction
function. at all.
Motor stops Fan does not
automatically. function.
Poor suction. Extraction
capacity
insufficient or
no extraction
at all.
Vibrations in Fan running
fan. unstable.
8

SPARE PARTS

The following spare parts are available:
0507060080/011113/H | SIF-700/900/1200/1500/1800/1900/2000 -|SF 7000/9000/12000/15000/18000/19000/20000
Freq.
Every 12
months
X
X
Possible cause Solution
No mains Check the mains
voltage. voltage.
Mains cord Repair or replace the
defective mains cord.
Loose contacts. Repair the contacts.
Thermal relay in Replace the thermal
system control relay.
panel defective.
Connection PTC Repair connection.
to frequency Refer to manual of
inverter frequency inverter.
defective.
Motor uses 2 Repair the phase
phases instead connection.
of 3.
Motor defective. Repair or replace the
motor.
Inverted Change the direction
direction of of rotation.
rotation of the
motor.
Inverted Change the direction
direction of of rotation.
rotation of the
motor.
Impeller(s) dirty. Clean impeller(s).
Undesired by- Check the flexible
pass. adapters.
Imbalance in Clean the fan.
fan.
Differential Clean or replace the
pressure of the filters of the
connected filter connected filter
system exceeds system.
capacity of the
fan.
Article no. Description
SIF-700 / SF-7000
0000102362 Fan wheel
0000102357 Motor 3 kW (4 HP)
SIF-900 / SF-9000
0000102269 Fan wheel
0000102358 Motor 5,5 kW (7.5 HP)
SIF-1200 / SF-12000
0000102363 Fan wheel
0321300140 Motor 7,5 kW (10 HP)
SIF-1500 / SF-15000
0000102364 Fan wheel
0321300130 Motor 11 kW (15 HP)
SIF-1800 / SF-18000
0000102365 Fan wheel
0000102359 Motor 15 kw (20 HP)
SIF-1900 / SF-19000
0000102366 Fan wheel
0000102360 Motor 18,5 kW (25 HP)
SIF-2000 / SF-20000
0000102367 Fan wheel
0000102361 Motor 22 kW (30 HP)
9

DISPOSAL

After life of the product, dispose it of in accordance with state or
local regulations.

EC DECLARATION

CE declaration of conformity for machinery
We, Plymovent Manufacturing B.V., Wezelkoog 11, 1822 BL
Alkmaar, the Netherlands, herewith declare, on our own
responsibility, that the products:
- SIF-700 / SF 7000 LI/RI (Outdoor)
- SIF-900 / SF 9000 LI/RI (Outdoor)
- SIF-1200 / SF 12000 LI/RI (Outdoor)
- SIF-1500 / SF 15000 LI/RI (Outdoor)
- SIF-1800 / SF 18000 LI/RI (Outdoor)
- SIF-1900 / SF 19000 LI/RI (Outdoor)
- SIF-2000 / SF 20000 LI/RI (Outdoor)
which this declaration refers to, are in accordance with the
conditions of the following Directives:
- Machine Directive 2006/42 EC
- LVD 2006/95 EC
- ErP Directive 2009/125/EC
Alkmaar, the Netherlands, November 1, 2013
.
Ir. F. Coehoorn
Vice President Research & Development
An installation is defined as a combination of several finished products
or components that are assembled by an installer at a given place. The
various parts of the installation are intended to operate together in a
particular environment and to perform a specific task. The entire
installation must comply with the relevant directives and standards. The
assembly instructions given by the manufacturer, as well as the whole
method of installation, must be in accordance with good engineering
practices within the context of installations, as well as installation rules.
Considering the above, the installer will be responsible for completing the
installation and issuing the final CE Declaration of Conformity.
EN - 6