Inhaltsverzeichnis; Setup - Sony CPD-E530 Bedienungsanleitung

Table of Contents
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Preset mode timing table . . . . . . . . . . . . . . . . . . . . . i
TCO'99 Eco-document . . . . . . . . . . . . . Back Cover

Setup

1
Connecting your monitor to your
computer
x To connect to the HD15 input connector
to HD15 video signal cable
(supplied)
Connecting to a Macintosh or compatible
computer
When connecting this monitor to a Power Mac G3/G4 computer,
use the supplied adapter if necessary. Connect the supplied adapter
to the computer before connecting the cable. If you connect to
another version of Macintosh series computer, having 2 rows of
pins, you will need a different adapter (not supplied).
2
Turning on the monitor and computer
1
Connect the power cord to the monitor and press the
! (power) switch to turn on the monitor.
2
Turn on the computer.
No need for specific drivers
This monitor complies with the "DDC" Plug & Play standard and
automatically detects all the monitor's information. No specific driver
needs to be installed to the computer.
The first time you turn on your PC after connecting the monitor, the setup
Wizard may appear on the screen. In this case, follow the on-screen
instructions. The Plug & Play monitor is automatically selected so that you
can use this monitor.
Notes
• Do not touch the pins of the video signal cable connector.
• Check the alignment of the HD15 connector to prevent bending the pins
of the video signal cable connector.
• Trinitron
• Macintosh is a trademark licensed to Apple Computer, Inc., registered in
• Windows
• IBM PC/AT and VGA are registered trademarks of IBM Corporation of
• VESA and DDC
•
• All other product names mentioned herein may be the trademarks or
• Furthermore, " ä " and " â " are not mentioned in each case in this manual.
To select the input signal
You can connect two computers to this monitor using the HD15
connectors. To select one of the two computers, use the INPUT
switch. The selected connector appears on the screen for 3 seconds.
Note
If no signal is input to the selected connector, NO SIGNAL appears on the
screen. After a few seconds, the monitor enters the power saving mode. If
to HD15 of the
this happens, switch to the other connector.
connecting computer
The pin assignment of the HD 15 video signal cable
* DDC (Display Data Channel) is a standard of VESA.
â
is a registered trademark of Sony Corporation.
the U.S.A. and other countries.
â
and MS-DOS are registered trademarks of Microsoft
Corporation in the United States and other countries.
the U.S.A.
ä
are trademarks of the Video Electronics Standard
Association.
E S
NERGY TAR is a U.S. registered mark.
registered trademarks of their respective companies.
1 2 3 4 5
6 7 8 9 10
11 12 13 14 15
Pin No. Signal
1 Red
2 Green (Sync on
Green)
3 Blue
4 ID (Ground)
5 DDC Ground*
6 Red Ground
7 Green Ground
8 Blue Ground
Pin No. Signal
9 DDC + 5V*
10 Ground
11 ID (Ground)
12 Bi-Directional
Data (SDA)*
13 H. Sync
14 V. Sync
15 Data Clock
(SCL)*
3
GB