RIKO Nestro Gebrauchsanweisung Seite 13

OPERATION MANUAL
UNFOLDING THE STROLLER
In order to unfold the stroller, release the automatic lock (fig. 1),
and pull the stroller guiderail upward until fully unfolded (fig. 2, 3).
ASSEMBLY AND DISASSEMBLY OF WHEELS
To assemble the wheel, first mount the half axles to the suspension
of the pram.
Note! The half axles of the front wheels are longer than the half axles
of the rear wheels. Ensure that you are mounting the longer axles in
the front suspension (fig. 4)
Plug in the pointed end of the half axle into the hole on the suspension
(fig. 5). Locking will occur automatically. Then put the wheel on the half
axle and press until lock (fig. 6).
Note! Prior to use, make sure all wheels are properly mounted.
To dismount the wheels, press the button located in the central
part of the wheel (fig. 7) and remove the wheel from the axle (fig. 8).
Additionally, you may dismount the half axle. To do this, press the
button in the suspension and pull out the axle (fig. 9).
HANDLE HEIGHT ADJUSTMENT
It is possible to adjust the pram handle height. To perform the
adjustment, press down the round buttons on both sides of the handle
at the upper part, and then adjust the right height (Fig. 10).
PARKING BRAKE
The pram is equipped with a rear parking brake. To engage the
brake, press its lever down (Fig. 11). In order to disengage it, lift the
lever.
NOTE! Before starting to push the pram, make sure that the brake
has been disengaged.
NOTE! Always engage the safety brake, when you leave the pram
on an inclined surface.
NOTE! The brake is not designed for slowing down. It should be
engaged after the pram has been stopped completely.
NOTE! The pram is not designed for running.
SUSPENSION HARDNESS ADJUSTMENT
The pram is equipped with a suspension hardness adjuster. To
adjust, move the lever located under the suspension (fig. 12). Repeat
the action on all four wheels. The suspension has 2 settings: hard and
soft.
BOTTLE HOLDER
To attach the bottle holder slide it down onto a special hook located
above the handlebar adjustment (fig. 13). The bottle holder hook is
adjustable. Make sure it is always fixed in a position that will keep the
bottle in a vertical position.
FOLDING AND UNFOLDING CARRYCOT
The carrycot comes with special straps that allow it to be folded and
save space when it is not used. To unfold the carrycot, pull the straps
on both its sides in the direction indicated by arrows (fig. 14, 15). To
fold the carrycot, loosen the straps on both its sides in the direction
indicated by arrows (fig. 16, 17).
ROCKING CARRYCOT
The carrycot has a rocking mechanism when placed on a flat
surface. To use it, fold all 4 props on the bottom of the carrycot (fig. 18).
If you want to prevent the carrycot from rocking, unfold all 4 props so
that they protrude beyond the sides of the carrycot (fig. 19).
ATTACHING AND REMOVING THE CARRYCOT
In order to attach the carrycot press it into the pram frame so that
the adapters on both sides of the carrycot lock onto the catches on the
pram frame (fig. 20). They will lock in place automatically.
ATTENTION! Make sure the carrycot is attached correctly prior
to use.
To remove the carrycot press the buttons on the adapters at the
sides of the carrycot (fig. 21) and pull the carrycot upwards.
ADJUSTABLE CARRYCOT BACKREST
The carrycot has an adjustable back rest. To adjust the position
of the back rest, pull out the knob at the front of the carrycot and turn
it left or right (fig. 22).
CARRYCOT VENTILATION
The carrycot comes with a ventilation system. To open the vents,
pull the levers located at the front of the carrycot on both sides (fig. 23).
CARRYCOT CANOPY AND HANDLE
THE CARRYCOT
The carrycot comes with a canopy. Its frame also doubles up as a
handle for carrying the seat (this is a handle for carrying the carrycot
and not the entire pram).
ATTENTION! Before lifting the carrycot, position it upright
(perpendicular to the ground) whilst holding it by the handle.
The canopy is adjustable. To position the canopy press the round
plastic buttons near its base (fig. 24).
ASSEMBLING AND DISASSEMBLING THE SEAT
The seat should be assembled and disassembled the same way as
for the carrycot (see ATTACHING AND REMOVING THE CARRYCOT
fig. 25, 26).
The seat may be assembled with its front and back facing the
movement direction (Fig. 27, 28).
NOTE! Before starting to use the pram make sure that the seat has
been assembled correctly.
RESTRAINT SYSTEM
The seat is equipped with a 5-point restraint system (Fig. 29).
It should be used from the moment a baby starts to sit by itself.
Unfasten the belts, by releasing the forks from the central buckle, seat
the baby, adjust the length of the belts so that they fit closely to the
baby's body, without oppressing it, and then fasten the forks of all the
belts to the central buckle.
The seat has an additional crotch strap which should be attached
to the safety bar using snaps (fig. 30). This is an additional element
and not be a substitute for using the 5 point safety harness.
NOTE! Always use the restraint system, if the baby can sit by itself.
SAFETY BAR
To attach the bar, insert its tongues into the slots in armrests.
To remove it, push the buttons located on the bottom of the slots
(fig. 31).
The bar is adjustable. You can detach one of its ends and move it
sideways to place the baby inside the carriage (fig. 32).
NOTE: The bar is an extra element and you must still use the five-
element harness to secure the child.
ADJUSTING THE LEG REST
The pram is equipped with an adjustable leg rest. To move it to the
right position, press down the buttons on its both sides (Fig. 33, 34).
ADJUSTING THE BACKREST
The seat unit can be adjusted to 4 different positions. To adjust
the position of the seat unit, unzip the back of the seat unit (fig.
35). The zip serves to conceal excess material when the backrest
is in a sitting position. To lower the backrest, pull the lever in the rear
(fig. 36). To lift the backrest, push it upwards. It will automatically click
into position (fig. 37).
CANOPY
To attach the canopy, insert its tongues into the slots in armrests
(fig. 38). To remove the canopy, push the buttons in the rear of slots
and pull it in the direction indicated by arrow (fig. 39).
The position of the canopy is adjustable. To adjust the position,
pull the front of the canopy forward or backward (fig. 40).
The canopy has an additional section that can be pulled forward.
FOR CARRYING
To unfold the additional section, open the zip in the rear of the canopy
(fig. 41).
RAIN FOIL
The pram is provided with a rain foil equipped with an air hole
at the baby's face height. To assemble it, put one end under the leg
rest or under the carrycot rear, and pull the other end onto the canopy
(Fig. 42, 43). The foil is suitable both for the deep and stroller version.
MOSQUITO NET
The carrycot comes with a mosquito net. To put it in place, attach
one end to the inside of the canopy using zips and stretch the other
end over the rear of the carrycot. Attach the sides of the mosquito net to
the canopy using the hook and loop fasteners (fig. 44).
INSTALLING THE CAR SEAT WITH ADAPTERS
Push the adapters into catches situated on the stroller's frame
(fig. 45) and then push the car seat's catches into the adapters (fig. 46).
The car seat has an adjustable handle. To position it, push the
buttons located at its feet.
REMOVING THE CAR SEAT AND ADAPTERS
To remove the car seat, push both buttons located on its sides
(fig. 47) and pull the handle upwards.
To remove the adapters, push both buttons situated on their inner
side and pull them upwards (fig. 48).
FOLDING THE PRAM
Prior to folding the pram, dismount the seat or carrycot.
To fold the frame, press the button located on the top right of the
guide (fig. 49A), then pull up the levers located on both sides of the
guide (fig. 49B) and push it forward until fully folded (fig. 50, 51, 52).
13