RIKO NATURO Gebrauchsanweisung Seite 13

OPERATION MANUAL
UNFOLDING THE STROLLER
In order to unfold the stroller, release the automatic lock (fig. 1),
and pull the stroller guiderail upward until fully unfolded (fig. 2, 3).
ATTACHING AND DETACHING REAR WHEELS
To attach rear wheels you must first attach the half axles in rear
suspension. Slide the pointed end of the half axle into the opening in rear
suspension (fig. 4). It should automatically click in place. Then slide the
wheel onto the half axle and push until it clicks in place (fig. 5).
NOTE! Before starting to use the pram, make sure that all the wheels
have been assembled correctly.
To disassemble the rear wheels, press down the button in the
central part of the wheel (Fig. 6) and remove the wheels from the axle
(Fig. 7). To detach the rear half axle push the button in rear suspension
and remove the half axle (fig. 8).
ASSEMBLING AND DISASSEMBLING THE FRONT SWIVELLING
WHEELS
In order to assemble the front wheels, force their axles in the ends of
the front legs, until you hear a characteristic "click" (Fig. 9). In order to
disassemble the wheels press down the button at the upper part of the
swivelling mechanism (Fig. 10) and slide the wheel axle in.
The stroller has swivel wheels, which may be locked in a forward
facing position. In order for the wheels to swivel, twist the knob in the
upper part of the wheel mount in an anti-clockwise direction. To lock the
wheels turn the knob in a clockwise direction (fig. 11).
HANDLE HEIGHT ADJUSTMENT
It is possible to adjust the pram handle height. To perform the
adjustment, press down the round buttons on both sides of the handle at
the upper part, and then adjust the right height (Fig. 12).
PARKING BRAKE
The pram is equipped with a rear parking brake. To engage the brake,
press its lever down (Fig. 13). In order to disengage it, lift the lever.
NOTE! Before starting to push the pram, make sure that the brake has
been disengaged.
NOTE! Always engage the safety brake, when you leave the pram on
an inclined surface.
NOTE! The brake is not designed for slowing down. It should be
engaged after the pram has been stopped completely.
NOTE! The pram is not designed for running.
ADJUSTING SUSPENSION STIFFNESS
It is possible to adjust the stiffness of the pram's rear suspension.
The stiffness is adjusted using the lever under the rear suspension
(fig. 14). Repeat for both rear wheels. The suspension has two settings:
stiff and soft.
EXTRA SHOCK ABSORPTION OF THE BASSINET AND SEAT UNIT
The baby carriage comes with extra shock absorption system for the
bassinet and seat unit. The shock absorbers are adjustable. For a firm
ride, turn the knob in the lower section of the shock absorber clockwise.
For a soft ride, turn the knob anticlockwise (fig. 15).
BOTTLE HOLDER
To attach the bottle holder slide it down onto a special hook located
above the handlebar adjustment (fig. 16). The bottle holder hook is
adjustable. Make sure it is always fixed in a position that will keep the
bottle in a vertical position.
ATTACHING AND REMOVING THE CARRYCOT
In order to attach the carrycot press it into the pram frame so that the
adapters on both sides of the carrycot lock onto the catches on the pram
frame (fig. 17). They will lock in place automatically.
ATTENTION! Make sure the carrycot is attached correctly prior to use.
To remove the carrycot press the buttons on the adapters at the sides
of the carrycot (fig. 18) and pull the carrycot upwards.
RECLINING CARRYCOT SUPPORT
The carrycot support is reclinable. To recline it into suitable position,
push and turn the knob located under the carrycot (fig. 19).
VENTILATED CARRYCOT
The carrycot is ventilated. To open the vent holes, slide the air grate
located under the carrycot (fig. 20).
CARRYCOT CANOPY AND HANDLE FOR CARRYING THE
CARRYCOT
The carrycot comes with a canopy. Its frame also doubles up as a
handle for carrying the seat (this is a handle for carrying the carrycot and
not the entire pram).
ATTENTION! Before lifting the carrycot, position it upright
(perpendicular to the ground) whilst holding it by the handle.
The canopy is adjustable. To position the canopy press the round
plastic buttons near its base (fig. 21).
ASSEMBLING AND DISASSEMBLING THE SEAT
The seat should be assembled and disassembled the same way as
for the carrycot (see ATTACHING AND REMOVING THE CARRYCOT
fig. 22, 23).
The seat may be assembled with its front and back facing the
movement direction (Fig. 24, 25).
NOTE! Before starting to use the pram make sure that the seat has
been assembled correctly.
RESTRAINT SYSTEM
The seat is equipped with a 5-point restraint system (Fig. 26). It
should be used from the moment a baby starts to sit by itself. Unfasten
the belts, by releasing the forks from the central buckle, seat the baby,
adjust the length of the belts so that they fit closely to the baby's body,
without oppressing it, and then fasten the forks of all the belts to the
central buckle.
The seat has an additional crotch strap which should be attached to
the safety bar using snaps (fig. 27). This is an additional element and not
be a substitute for using the 5 point safety harness.
NOTE! Always use the restraint system, if the baby can sit by itself.
SAFETY BAR
To attach the bar, insert its tongues into the slots in armrests. To
remove it, push the buttons located on the bottom of the slots (fig. 28).
The bar is adjustable. You can detach one of its ends and move it
sideways to place the baby inside the carriage (fig. 29).
NOTE: The bar is an extra element and you must still use the five-
element harness to secure the child.
ADJUSTING THE LEG REST
The pram is equipped with an adjustable leg rest. To move it to the
right position, press down the buttons on its both sides (Fig. 30, 31).
ADJUSTING THE BACKREST
The seat unit can be adjusted to 4 different positions. To adjust the
position of the seat unit, unzip the back of the seat unit (fig. 32). The
zip serves to conceal excess material when the backrest is in a sitting
position. To lower the backrest, pull the lever in the rear (fig. 33). To lift the
backrest, push it upwards. It will automatically click into position (fig. 34).
CANOPY
To attach the canopy, insert its tongues into the slots in armrests
(fig. 35). To remove the canopy, push the buttons in the rear of slots and
pull it in the direction indicated by arrow (fig. 36).
The position of the canopy is adjustable. To adjust the position, pull the
front of the canopy forward or backward (fig. 37).
The canopy has an additional section that can be pulled forward. To
unfold the additional section, open the zip in the rear of the canopy (fig.
38).
RAIN FOIL
The pram is provided with a rain foil equipped with an air hole at
the baby's face height. To assemble it, put one end under the leg rest
or under the carrycot rear, and pull the other end onto the canopy
(Fig. 39, 40). The foil is suitable both for the deep and stroller version.
MOSQUITO NET
The carrycot comes with a mosquito net. To put it in place, attach one
end to the inside of the canopy using zips and stretch the other end
over the rear of the carrycot. Attach the sides of the mosquito net to the
canopy using the hook and loop fasteners (fig. 41).
INSTALLING THE CAR SEAT WITH ADAPTERS
Push the adapters into catches situated on the stroller's frame
(fig. 42) and then push the car seat's catches into the adapters (fig. 43).
The car seat has an adjustable handle. To position it, push the buttons
located at its feet.
REMOVING THE CAR SEAT AND ADAPTERS
To remove the car seat, push both buttons located on its sides
(fig. 44) and pull the handle upwards.
To remove the adapters, push both buttons situated on their inner side
and pull them upwards (fig. 45).
FOLDING THE STROLLER
Before folding the stroller, remove the child seat or the carrycot.
To fold the stroller frame, push the button on the upper part of
the guide on the right side (fig. 46A), then pull up the levers on both
sides of the guide (fig. 47B) and push them down until total folding
(fig. 47, 48, 49).
13