Accessories - Flott PBS 150 ST Gebrauchsanleitungen Und Wartung

ATTENTION: Never hold the pieces to be cut in
your hand.
Fig. 11
When the pieces to be cut are profi led sections, fl at pieces or
special shapes, refer to the examples shown in the fi gures.
If the thickness of the profi led section is to be very thin, an
outline should be fi tted which copies the profi le inside the
profi led section itself to stop it being crushed between the
jaws.
4.7 CUTTING TABLE
5

ACCESSORIES

5.1 CHOISE OF BLADE
Your sawing machine is equipped with a bi-metal blade
measuring 1735x13x0,9 mm with variable toothing 6/10
teeth per inch, for use in the majority of cuts possible with this
machine. For special requirements (see cutting table point
4.7), for example, for cutting large solid sections or profi led
sections or corner pieces of small thickness, there are also
blades avail-able with 4/6 toothing or 14 teeth per inch.
MATERIAL: ................ M42 (steel for springs ÷ steel HSS)
EXTENSION: .......................................................mm 1735
HEIGHT: ...................................................................mm 13
THICKNESS:...........................................................mm 0,9
TOOTHING: ..................................................standard 6/10
...................................................................optional 4/6 - 14
5.2 FITTING THE BASE PLATE (Fig. 3)
(where included)
The fasten the machine to the base plate, use the four screw
A, four nuts B and four Washer C conteined in yhe carton
box of the base plate.
Put the four screws A into the holes of the base of the
machine, and fasten the whole with the four nuts B.
6 MAINTENANCE
6.1 REGULAR MAINTENANCE
The operations of ordinary maintenance, which may also be
performed by non-specialist personnel, are all described in
the previous sections and here below.
1. Before performing any maintenance operation, disconnect
the machine electric plug from the wall outlet.
2. During maintenance operations, always wear personal
protection (safety goggles and gloves).
3. Remove the processing residues from the cutting area
and the blade guides whenever necessary.
You are advised to use a suction device or a brush.
ATTENTION: Do not use jets of compressed air.
If you do not intend to use the sawing machine for a long
time, clean it and put it in a dry place if possible.
In these cases it is advisable to slacken off the blade so that
it is not kept tight for no reason.
6.2 ASSISTENCE
Should it be necessary to call qualified personnel for
operations of extraordinary maintenance, or in the case of
repairs, under guarantee or at a later date, you should always
contact an authorized service centre or the factory directly, if
there is no service centre in your area.
6.3 DISPOSAL OF THE MACHINE AND PACKAGING
NFORMATION FOR USERS
In accordance with art. 13 of Legislative Decree
25th July 2005, no. 151 "Implementation
of Directives 2002/95/EEC, 2002/96/EEC
and 2003/108/EEC, relative to reducing the
use of hazardous substances in electrical and electronic
appliances and the disposal of waste", please take note of
the following:
• The crossed out wheelie bin symbol found on the ap-
pliance or on the packaging, indicates that the product
must be disposed of separately from ordinary house-
hold waste when it reaches the end of its working life.
• The user must consign the unwanted appliance to an
authorized differentiated waste disposal centre for elec-
trical and electronic goods, or alternatively, hand it over
to the relative dealer on purchasing a new appliance of
the same type on the basis of a one to one ratio.
• Differentiated disposal, to enable possible recycling or
environmentally compatible elimination of the applian-
ce, helps to limit undesirable effects on health and the
environment and promotes the reuse and/or recycling of
the materials which went into making up the appliance.
WARNING: Sanctions, in accordance with the
relative legislation in force in the country of use,
will be imposed on the user if the appliance is
disposed
11