Herunterladen Inhalt Inhalt Diese Seite drucken

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

LCD MOUNT INSTALLATION
31554/31555
INSTRUCTIONS
Before beginning the installation of your new LCD mount, first verify that you have all of
the necessary tools at hand. The following tools are required for proper installation:
√ Phillips screwdriver
√ Stud finder for drywall installation
√ Electric drill and 8mm masonry bit for concrete/brick installation
Also make sure that all of the hardware has been included with your mount.
You should find the following:
(Ref ) Item (Qty)
(A) Drywall Screw M6x65 (x2)
(B) Concrete Anchor (x2)
(C) M4x12 Bolt (x4)
(D) M4x30 Bolt (x4)
(E) Spacer (x4)
(F) 3 mm Allen Key (x1)
(G) 4 mm Allen Key (x1)
Step 1 – Mounting the Wall Piece Drywall Installation
IMPORTANT: The weight of the LCD requires installation into a wood stud.
Failure to do so may result in damage or injury.
Use a stud finder to locate a wood stud where you want to install
your mount. It is recommended that you verify the location of the stud
using a small nail or an awl. You should use the center of the stud.
After the stud has been located, place the wall piece against the wall
with the hook towards the bottom. Secure the wall piece using one
Drywall Screw (A), but do not completely tighten yet. Using the
integrated bubble guide, carefully adjust the wall piece until it is level.
Insert the remaining screw and tighten both screws.
Concrete/Brick Installation
Begin by placing the wall piece into position against the wall with the
hook towards the bottom. Using the integrated bubble guide to keep
it level, mark off the holes that will be used for securing the mount and
place the wall piece aside. Next, drill holes using an electric drill and
8mm masonry bit. Remove any excess dust from the holes and insert a
Concrete Anchor (B) into each hole. If necessary, use a hammer to
lightly tap each anchor into place so that they are flush with the wall.
Once both anchors are in place, put the wall piece back into position.
Attach the wall piece using the Drywall Screws (A) provided.
Make sure both screws are secure.
31554-31555 Manual.indd 1
04-06-2009 08:56:39

Werbung

Inhaltsverzeichnis
loading

Inhaltszusammenfassung für Grundig 31554

  • Seite 1 Once both anchors are in place, put the wall piece back into position. Attach the wall piece using the Drywall Screws (A) provided. Make sure both screws are secure. 31554-31555 Manual.indd 1 04-06-2009 08:56:39...
  • Seite 2: Final Installation

    If your mount does not have a knob, use the Allen Wrench (G) from your hardware kit to tighten or loosen the nut at the joint. 31554-31555 Manual.indd 2 04-06-2009 08:56:40...
  • Seite 3: Schritt 1 - Befestigung Des Wandelements Bei Trockenwandmontage

    Dübel leicht hineinzuklopfen, bis sie bündig mit der Wand sind. Nach dem Einset- zen der Dübel halten Sie das Wandelement wieder in Montageposition gegen die Wand. Befestigen Sie das Wandelement mit den mitgelieferten Trockenwand- schrauben (A). Stellen Sie sicher, dass beide Schrauben festgezogen sind. 31554-31555 Manual.indd 3 04-06-2009 08:56:41...
  • Seite 4: Schritt 3 - Endgültige Montage Und Betrieb

    Uhrzeigersinn zum Anziehen und entgegen dem Uhrzeigersinn zum Lösen. Wenn Ihr Halter keinen Knopf hat, verwenden Sie den Inbusschlüssel (G), der mit den Beschlägen mitgeliefert wurde, um die Mutter an der Verbindung festzuziehen oder zu lösen. 31554-31555 Manual.indd 4 04-06-2009 08:56:41...
  • Seite 5: Stap 1 - Het Wandgedeelte Bevestigen (Installatie In Gipsplaat)

    Als beide ankers zijn aangebracht, plaatst u het wandgedeelte terug. Bevestig het wandgedeelte met de meegeleverde gipsplaatschroeven (A). Draai beide schroeven helemaal vast. 31554-31555 Manual.indd 5 04-06-2009 08:56:42...
  • Seite 6 Als de steun geen instelknop heeft, gebruikt u de inbussleutel (G) uit het hardwarepakket om de moer op het scharnier strakker of losser te draaien. 31554-31555 Manual.indd 6 04-06-2009 08:56:42...
  • Seite 7 Une fois les deux dispositifs d'ancrage en place, re- mettez la pièce murale en place. Attachez la pièce murale en utilisant les vis pour panneau mural (A) fournies. Veillez à ce que les deux vis soient bien fixées. 31554-31555 Manual.indd 7 04-06-2009 08:56:43...
  • Seite 8 Si votre support n'en a pas, utilisez la clé Allen (G) qui se trouve dans vos pièces pour serrer ou desserrer l'écrou de l'articulation. 31554-31555 Manual.indd 8 04-06-2009 08:56:44...

Diese Anleitung auch für:

31555

Inhaltsverzeichnis