Unblocking The Electromechani- Cal Brake; Lifting And Transport: Ma- Chine, Battery And Battery Charger; Technical Informations; General Description - LAVOR Pro Comfort XXS 66 BT Handbuch

tional battery.
After moving the machine away from all the pack-
ing, start mounting the accessories and the batter-
ies as per the instructions provided in the specific
section.
Keep all the pieces of the packing since they might
be useful in the future to protect the machine and
the accessories during transport to another loca-
tion or to authorised service centres. If not, the
packing can be disposed in accordance with current
disposal laws.
4.4 UNBLOCKING
CHANICAL BRAKE
When the machine is switched off or with-
out batteries the electromechanical brake is
blocking the machine and it is not possible to
move it.
To unblock the electromechanical brake it is nec-
essary to operate on the traction motor placed on
the rear wheel axle (Photo L) following the proce-
dure mentioned here below:
- Pull the unblocking lever (Photo L - 1) outwards
- Rotate the lever downwards and block the lever
on the pin placed on the motor in order that the
lever will be fixed in the outer position (Photo L - 2).
The mechanical brake is now unlocked and it
is now possible to move the machine.
Once the machine have been moved, it is neces-
sary to carry out the same procedure on the con-
trary in order to replace the lever in the machine
working position ( Photo L - 1 ).
WARNING: Before using the machine be
sure that the unblocking lever is in the ma-
chine working position ( Photo L - 1 ).
4.5 LIFTING AND TRANSPORT: MA-
CHINE, BATTERY AND BATTERY CHARGER
Never use a forklift truck to lift the machine.
There are no places on the frame that can be used
to lift the machine directly.
Before preparing the packing and transporting the

machine:

- Empty the recovery tank and the detergent solu-
tion tank.
- Disassemble the squeegee and the brushes or
pad drivers.
- Disconnect and remove the batteries.
Place the machine on the original pallet (or an
equivalent one that can bear the weight and is big
enough for the machine's overall dimensions) using
an inclined surface.
Solidly anchor the machine and the squeegee to
the pallet using metallic brackets or other elements
that can bear the weight of the parts.
Lift the pallet with the machine and load it on the
transport vehicle.
THE ELECTROME-
Secure the machine and the pallet using ropes con-
nected to the transport vehicle.
As an alternative, when using private transport
vehicles, use inclined ramps to push the machine
without the pallet, making sure to protect all parts
and the machine itself against violent impacts, hu-
midity, vibrations and accidental movements during
transport.
The battery boxes have holes where tools can be
hooked for handling.
To lift or insert the battery (into the machine
compartment), use only suitable personnel and
equipment (cables, eyehooks, etc.) for the opera-
tion and to bear the weight of the loads involved.
When transporting, take the same precautions and
follow the same instructions provided for the ma-
chine together with those in the special manufac-
turer's manual.
The battery charger can be transported on its sup-
ports, both vertically and horizontally. Take the
same precautions and follow the same instructions
provided for the machine together with those in the
special manufacturer's manual.

5. TECHNICAL INFORMATIONS

5.1

GENERAL DESCRIPTION

5.1.1 MACHINE
We can summarise the machine's main features as
follows:
- The form of the squeegee, the air flows and the
specially designed rubber blades produce excellent
drying results even on tiled floors. Thanks to the
particular balanced shape of the machine frame
and the squeegee support, no water residues are
left behind in a curve, and even when a smaller
squeegee is used.
- Excellent distribution of weights and geometries:
the centre of gravity is very low, also thanks to the
very heavy brush plate and because the batteries
are located at the level of the wheels.
- A heavy weight on the brushes makes them work
efficiently on the floor. The pressure is generated
by the weight of the plate, without springs or ad-
ditional devices that lead to difficulties and inaccu-
racy. The entire mass is generated by the hanging
weight of a 15 mm steel ship's plate.
- A large volume of water in the tanks reduces
dead time since fewer trips are needed to collect
water and dump dirt. There is no delicate flexible
diaphragm that, at a technical level, is difficult to
clean.
- A few dozen litres of water in the recovery tank
are used to decant any foam (dangerous for the
suction motor).
- The traction system is designed for the machine
weights, making the machine responsive and easy
to handle.
- Robust construction. The frame and the squee-
gee, built with thick sheet metal - thickness 6 mm,
8 mm, 10 mm up to 20 mm – are laser cut and
31