General Information; Manual Purpose; Terminology And Symbol Legend; Product Identification - LAVOR Pro Comfort XXS 66 BT Handbuch

2. GENERAL INFORMATION

2.1

MANUAL PURPOSE

To make it easier to read about and look up vari-
ous subjects, refer to the table of contents at the
beginning of the section in your language.
This manual has been prepared by the manufac-
turer and is an integral part of the product. As
such, it must be kept in a safe place for the ma-
chine's entire service life until demolition.
The customer must ensure that machine operators
have read or are familiar with the contents of this
manual so that they strictly follow the instructions
described herein.
Constant compliance with the instructions provided
in this manual is the only way to guarantee the
best results in terms of safety, performance, ef-
ficiency and service life of the product you now
own. Non-compliance with these rules may cause
injuries to people and damage to the machine, the
scrubbed surface and the environment: in no case
can such injuries or damage be attributed to the
manufacturer.
This manual refers in detail to the machine and
provides instructions and descriptions only about
our batteries and battery chargers (optional).
The batteries and the battery charger are basic
complementary machine parts and will affect its
operation in terms of running time and perfor-
mances. Only the correct combination of the two
accessories (batteries and battery charger) will en-
sure the highest possible performances and avoid
wasting lots of money. For more detailed informa-
tion refer to the special battery and battery charger
manuals.
Our recommended battery chargers and batteries
(optionals) ensure the best combination with the
machine and offer outstanding versatility (battery
charger) as well as the category's highest quality
and performance standards.
2.2 TERMINOLOGY AND SYMBOL LEG-
END
For the sake of clarity and to efficiently highlight
the various aspects of the instructions provided,
terms and symbols were used that are defined and
illustrated here below:
- Machine. This definition replaces the commercial
name to which this manual refers.
- Operator. An operator is considered the person
who normally uses the machine and is familiar with
its operating features but does not have the spe-
cific technical skills to work on that machine.
- Technician. A technician is considered a person
who has the experience, technical education, leg-
islative and regulatory knowledge that allows him
to carry out any type of required work, and the
ability to recognise and to avoid possible risks dur-
ing machine installation, operation, handling and
maintenance.
- INDICATION SYMBOL (
☞
) Particularly im-
28
portant information to avoid machine malfunctions.
- ATTENTION SYMBOL (
formation to avoid serious damage to the machine
and to the environment in which it operates.
- DANGER SYMBOL (
avoid serious (or extreme) consequences affecting
the health of persons and causing damage to the
product and the environment in which it operates.
2.3

PRODUCT IDENTIFICATION

The nameplate located under the dashboard,
above the battery connector, contains the follow-
ing information:
• manufacturer ID
• CE mark
• model code
• model
• overall power rating
• serial number
• year built
• weight with maximum load
2.4

SPECIFIC USE

This machine is a floor scrubber-drier: it must be
used to scrub and to vacuum liquids of flat, rigid,
horizontal, smooth or moderately rough and uni-
form floors that are free from obstacles in both
civic and industrial environments. Any other use
is prohibited.
Please refer very carefully to the safety information
reported in this manual.
The scrubber-drier distributes a quantity of a water
and detergent solution (adjustable) on the surface
to be cleaned, while the brushes remove any dirt
on the ground. The machine's suction system,
using a ground squeegee, perfectly dries the liquids
and the dirt just removed from the front brushes
in a single pass.
By efficiently combining a cleaning detergent with
various types of brushes (or abrasive disks), the
machine can adapt to all the various combinations
of floors and dirt.
2.5

TECHNICAL MODIFICATIONS

This machine was designed and built in accord-
ance with the fundamental requirements for user
safety and health as set forth in European direc-
tives. For this reason the CE mark was placed on
the ID label. The European directives to which the
equipment conforms are referenced in the Certifi-
cate of conformity annexed to this manual. This
certificate will no longer be valid if the equipment
is modified in any way without the manufacturer's
prior authorisation.
The manufacturer reserves the right to make tech-
nical modifications to the product, without prior
notice, in order to make the necessary technical
upgrades or improvements. For this reason, some
details of your machine may be different from the
information in the sales catalogues or from the il-
) Very important in-
) Vital information to