GBD GECO LUX series Montageanleitung Seite 11

PROFESSIONAL AUTOMATIC SYSTEM FOR GATES AND GARAGE DOORS
Ensure that the deceleration phase starts at least 150 mm before complete closure of the door. If not, adjust the closing limit
switch, anticipating the intervention.
11 Adjust the automatic reclosing time, if required, by turning the trimmer RV1 clockwise.
12 Adjust the thrust force with the trimmer RV2 in such a way that with a moderate force of the operator you obtain the following:
• Stopping of the door if in the opening or braking phase;
• Par tial reopening of the door if in the closing phase.
13 Repeat the opening manoeuvre several times in order to optimise the above described adjustments.
14 Check proper functioning of the safety devices, bearing in mind that:
• When the STOP button is pressed, the operator locks all its movements and waits for a START command.
• The photocell inter vention during the opening phase does not activate any operation.
• The photocell inter vention during the closing phase, may cause two dif ferent behaviours of the operator:
- if DIP SWITCH (1) is in the OFF position, the photocell inter vention locks the movement;
- if DIP SWITCH (1) is in the ON position, the photocell inter vention causes immediate reopening until reaching the opening
position.
• The inter vention of the maximum thrust sensor of the operator during the opening phase causes immediate stopping of the movemen
• The inter vention of the maximum thrust sensor of the operator during the closing phase causes reopening of the door for
about 1 sec.
15 Enable, if required, the supplementar y functions:
• Pre-flashing: causes the flashlight to come on 3 sec. before star ting the door movement; it is enabled by setting the DIP SWITC
to the ON position.
Use of built-in radio "for version AS02180"
Radio control code programming
Photo 22 1 Press the LEARN (S2) button on the control unit. The red light - DL2 - comes on for 5 sec.
2 Press the radio control button before the 5 sec. elapse. When the red light flashes it means that the code has been
stored correctly.
3 To store fur ther codes repeat the above described procedure.
When the previously stored radio control button is pressed, a START command is executed.
Each time the radio control button is pressed, the red light indicates, by flashing, that the signal has been received correctl
N.B. A maximum of 200 codes can be stored.
WARNING: If the red light flashes fast when the LEARN (S2) button is pressed, it means that the code memory is full and further
radio controls cannot be stored.
All the stored codes can however be deleted.
Deleting the codes
1 Hold the LEARN (S2) button pressed down until the red light - DL2 - emits a signal that deletion has been completed.
WARNING: The deletion will cause the loss of all the radio codes and the radio controls will have to be reprogrammed.
Use of the plug-in radio "for version AS02190"
Photo 23
Provision has been made on the control unit version AS02190 to plug in the original Gi.Bi.Di. plug-in radio card.
For installation follow the instructions that come with the radio.
Accessories
•
Photo 24 Semaphore card
The card is fixed to the unit by means of the transformer screw and is connected with a special cable to the outlet which
you should weld in the stopping place "SEMAPHORE".
The card has 2 clean-contact outputs (relay 10A 230 VAC max.) with the following operation:
• While the operator is of f during closing, both contacts are open.
• While the operator opens, one of the contacts is closed and the other open.
• While the door is open, the contacts remain set as in the opening phase.
• While it closes, the contact closed during opening opens and the other one closes.
•
Buffer battery
The buf fer batter y kit can be used when the 230 VAC mains power fails to ensure continued functioning of the operator.
During operation with only the buf fer batter y, the operator is slightly slower and the cour tesy lamp is disabled.
The batter y must be connected to the "EMRG" (positive pole) terminal and to the "GND" (negative pole) terminal.
Warning: Connecting batteries directly to the terminals causes irreversible damage to the control unit.
Use only the special Gi.Bi.Di battery kit for the drive unit.
•
External unlocking kit
•
Arm for counterweight doors
11
English
t.
H (3)
y.