Werbung
Quicklinks
Instruction manual / Montageanleitung
SPECIFICATIONS
Wingspan:........................1630mm (64.1in.)
Length:................................1170mm (46in.)
Electric Motor:.....................See next pager
RTF Weight: 2.6Kg / 5.7lbs (Will vary with
Equipment Used).
Radio:....................6 Channel / 6 Servos
Function: Ailerons-Flaps-Elevator-Rudder-Motor
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
Radio control model / Flugmodel
ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY
TECHNISCHE DATEN
Spannweite:...................................1630mm
Lange:............................................1170mm
Elektroantrieb.............(siehe nächste Seite)
Brushless Motor:.............
Fluggewicht:.......................................2.6Kg
Fernsteuerung................6 Kanal / 6 Servos
Werbung
Verwandte Anleitungen für VQ Radio Control Model Scooter
Inhaltszusammenfassung für VQ Radio Control Model Scooter
- Seite 1 Radio control model / Flugmodel ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY Instruction manual / Montageanleitung TECHNISCHE DATEN SPECIFICATIONS Wingspan:......1630mm (64.1in.) Spannweite:........1630mm Length:........1170mm (46in.) Lange:..........1170mm Electric Motor:.....See next pager Elektroantrieb.....(siehe nächste Seite) RTF Weight: 2.6Kg / 5.7lbs (Will vary with Brushless Motor:.....
- Seite 2 REQUIRED FOR OPERATION (Purchase separately) # C5753 Propeller P-CON 12x6 # C2036 Servo Verlängerungskabel 400mm Servo Extension Cord 400mm # C2983 # C6741 LiPo LEMONRC 3700-11,1V Brushless Combo BOOST 40 inkl. Motor, Regler, Programmkarte # C4995 including motor, ESC and program card MASTER Digital Servo DS3012 oder/or # C5638 MASTER Digital Servo DS3012 MG...
- Seite 3 Pull the magnetic top hatch out of the fuselage. ! Align the mark on both mounts with the mark on the fuselage Using a pencil or felt tipped pen, mark the fire wall where the four holes are to be drilled. Remove the engine mounts and drill four 5mm holes as marked.
-
Seite 4: Side View
Using the aluminum mounting plate as template, mark the plywood motor mounting plate where the four holes are to be drilled (2A). Remove the aluminum mounting plate and drill 3mm hole through the plywood at each of the four marks marked (2B). Note: The aluminum motor mounting included with electric motor set. - Seite 5 Full the elevator out of the horizontal stabilizer. When you are satisfied with the alignment, use a pencil to trace around the top and bottom of the stabilizer where it meets the fuselage. Note: the rectangular hole on the center of the stabilizer must be coincidental with the center line of the fuselage.
- Seite 6 When you are satisfied with the alignment, Secure the horizontal stabilizer onto the fuselage using CA glue. Note: Glue on the top and bottom of the horizontal stabilizer, where it meets the fuselage, and inside the slot for the vertical stabilizer installation.
- Seite 7 Cut away only the covering. Control horn Note: The slots for the control horn ...2 installation are pre- cut at factory. When you are satisfied with the alignment, use a pencil to trace around the right and left of the stabilizer where it meets the fuselage.
- Seite 8 3x12mm screw ..2 3mm collar ..1 3mm collar 3x12mm screw Cut away only the covering. Note: The slots for the control horn installation are pre- cut at factory. Fuselage - bottom view Fuselage - bottom view 3x15mm screw Cut away only the covering 3X15mm screw ....4...
- Seite 9 To muffler Insert the fuel tank (in case of gas engine) or Li-po battery (in case of Electric motor) Filler tube Rubber stopper Stopper To engine Blow Water Checking for leaks - block the vents and blow into the feed - if in doubt submersing the tank in a blow of water will show up any problems.
- Seite 10 3mm set Screw Elevator and rudder pushrod D=5/64”(2mm) 2 mm Elevator and Rudder servo Rudder servo Linkage Stopper set Cut away only ....21 the covering 175mm pushrod ..2 Elevator servo Cut away only the covering 3mm set Screw Aileron and flap pushrod 6x22mm wooden dowel...
- Seite 11 Aluminum tube B’ Aluminum tube B=B’ Note: check the length (B=B’) of the aluminum tube with the fuselage before glue. 3x15mm screw ..2 Note: The holes on the surface of the top of the wing are pre-drilled at factory. Secure the wing in place using 3x15mm screw (B).
- Seite 12 BALANCE AND CONTROL SURFACE Aileron 10mm 10mm Querruderausschlag 20mm Rudder Flap 20mm Seitenruderausschlag 20mm 10mm Elevator 68 ~ 73mm 10mm Hohenruderausschlag Do not try to fly an out-of balance model! Uberprufen Sie vor dem Flug den Schwerpunkt. Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner IMPORTANT: to clean on surface of your model to keep the colour not fade.