Herunterladen Inhalt Inhalt Diese Seite drucken

Transport - CEMO HD 25 I Bedienungsanleitung

Pe-auffangwanne
Inhaltsverzeichnis

Werbung

GB
National Technical Approval
No. Z-40.22-549, dated 18 November 2016
Polyethylene collection trays (injection moulded) with a
containment volume of 25 I, 35 I, 60 I and 120 I; combined
as a surface protection system
Manufacture, packaging, transport and storage
1
Manufacture
The body of the containment units and grating (perforated plates) must be manufactured in
accordance with the requirements in the manufacturing description filed at the DIBt. The
injection moulding process shall be controlled such that the mould is completely filled with
moulding compound.
2
Packaging, transport and storage
2.1
Packaging
It is not necessary to package the containment units for purposes of transport or (temporary)
storage if the requirements of Section 2.2 are met.
2.2
Transport and storage
2.2.1
General
(1) Transport shall be carried out only by companies with specialist experience, suitable
machinery, equipment and means of transport, and adequately trained staff.
(2) To prevent danger to employees and third parties, the relevant accident prevention
regulations shall be observed.
2.2.2
Preparation for transport
(1) The containment units must be prepared for transport such that no damage occurs
during loading, transport and unloading.
(2) The loading surface of the transport vehicle must be designed to eliminate possible
damage to the containment units by impact or sharp objects.
2.2.3
Loading and unloading
When lifting, moving and setting down the containment units, impact loads must be avoided.
2.2.4
Carriage
(1) The containment units must be secured to prevent them moving around during carriage.
(2) The containment units must not be damaged by the securing method.
2.2.5
Storage
If temporary storage is required this must be on level ground clear of objects with sharp
edges. When stored outside, the containment
units should be protected from damage and storms.
2.2.6
Damage
Damaged containment units that are not in perfect working order must be taken out of
service.
Z41971.16
2. Transport, installation and
operating instructions
Dear customer,
The PE collecting trough
been conceived for practical use down to the last detail
and meets all official requirements for a problem-free use.
Details can be found in the following operating instruc-
tions. Thank you for trusting our product.
Your CEMO
1.
General information
1.1 Attention should be paid to the following documents
– Approval Z-40.22-549, for PE collecting trough
(operator extract)
– Regulations of the water, industrial and building
laws, hazardous substances law where applicable
– Inspection declaration
12
Annex 3
is a quality product that has
HD
1.2 Fields of use
The rectangular, open collecting troughs of polyethylene
(PE) can be used as a part of storage systems with mobile
containers.
They are provided for storing:
– used and unused engine and gear oils with flash
points above 100°C
– pesticides
– various acids, alkaline solutions, saline solutions
and chemicals according to the resistance list in the
approval.
2.

Transport

Pay special attention to the following to avoid damages
and maintain the warranty claims:
– do not drop or throw the collecting trough
– do not place on edges or sharp objects
3.
Installation conditions
The installation conditions for the respective media can
be found in the pertinent water, industrial and building law
regulations.
The PE collecting troughs should be installed on a firm,
level base.
4.
Maintenance
1.40.22-19/16
PE collecting troughs require no special maintenance.
The collecting trough should be checked regularly by the
operator according to its approval.
3. Inspection declaration
of HD-PE as a storage system for mobile
containers.
Article No.:
Approval number: Z-40.22-549
We confirm that the PE collecting trough
complies with the provisions of the general con-
struction inspection approval. The construction
and leak tests have been performed.
Inspection declaration
for PE collecting trough
211.X
Quality Assurance
HD
HD

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Hd 35 iHd 120 iHd 60 i

Inhaltsverzeichnis