Werbung
Verfügbare Sprachen
Verfügbare Sprachen
SIMATIC NET
Compact Operating Instructions
ANT795-6MP (omni antenna 2.4 / 5 GHz)
Copyright © Siemens AG 2019
The reproduction, transmission or use of this document or its contents is
not permitted without express written authority. Offenders will be liable for
damages. All rights, including rights created by patent grant or registration
of a utility or design, are reserved.
Disclaimer of liability
We have checked the contents of this manual for agreement with the
hardware and software described. Since deviations cannot be preclud-ed
entirely, we cannot guarantee full agreement. However, the data in this
manual are reviewed regularly and any necessary corrections included in
subsequent editions.
Technical data subject to change without prior notice.
Siemens AG
Digital Industries
Postfach 48 48
D-90026 NÜRNBERG
GERMANY
Security information
In order to protect plants, systems, machines and networks against cyber
threats, it is necessary to implement – and continuously maintain – a
holistic, state-of-the-art industrial security concept. Siemens' products and
solutions constitute one element of such a concept. For more information
about industrial security, please visit
https://www.siemens.com/industrialsecurity
Recycling and disposal
The products are low in pollutants, can be recycled and meet
the re-quirements of the WEEE directive 2012/19/EU for the
disposal of electrical and electronic equipment.
Do not dispose of the products at public disposal sites.
For environmentally friendly recycling and the disposal of your
old device contact a certified disposal company for electronic scrap or
your Siemens contact
https://support.industry.siemens.com/cs/ww/en/view/109479891.
Note the different national regulations.
Warning notice system
This manual contains notices you have to observe in order to ensure your
personal safety, as well as to prevent damage to property. The notices
referring to your personal safety are highlighted in the manual by a safety
alert symbol, notices referring only to property damage have no safety
alert symbol. These notices shown below are graded according to the
degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precau-
tions are not taken.
WARNING
indicates that death or severe personal injury may result if proper pre-
cautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are
not taken.
NOTICE
indicates that property damage can result if proper precautions are not
taken.
C79000-8974-C407-05
Release 05/2019
English
All rights reserved
Qualified Personnel
The product/system described in this documentation may be operated
only by personnel qualified for the specific task in accordance with the
relevant documentation, in particular its warning notices and safety
instructions. Qualified personnel are those who, based on their training
and experience, are capable of identifying risks and avoiding potential
hazards when working with these products/systems.
1 Safety notes
WARNING
Danger due to lightning strikes
Antennas installed outdoors must be within the area covered by a light-
ning protection system.
Make sure that all conducting systems entering from outdoors can be
protected by a lightning protection potential equalization system.
When implementing your lightning protection concept, make sure you
adhere to the VDE 0182 or IEC 62305 standard.
NOTICE
Improper use
The device (and its components) may only be used for the application
described in the catalog or the operating instructions. Combinations with
devices or components of other manufacturers are permitted it they have
been approved by Siemens.
Correct and safe operation of the device is guaranteed only when it is
transported, stored, set up, installed, used and maintained according to
the recommendations.
2 Components of the product
The following components are supplied with the antenna:
•
1x antenna with 1x N Connector female
•
Mounting material for securing the antenna to the mount
(1x toothed lock washer, 1x nut)
•
Mounting material for securing the mount
(2x U-bolts, 1x L-bracket, 4x washers, 4x spring washers,
4x nuts)
•
1x Compact Operating Instructions
Please check that the consignment you have received is complete. If it is
not complete or there are signs of external damage, please contact your
supplier or your local Siemens office.
3 Mounting (mast mounting)
When mounting and removing the antenna connection cable or the an-
tenna on the mount, you have to hold the hexagon nut of the antenna foot
in place with an open-ended wrench (size 30 mm).
1.
any oil and other contamination from the mounting parts.
Remove
2. Screw the antenna with the toothed lock washer and the nut on the
mount. The tightening torque of the nut is max. 12 Nm. (wrench size
21 mm).
3. Screw the U-bolts with one washer , one spring washer and a
nut to the L-bracket .
4. Screw the antenna connection cable (not included in the scope of
delivery) to the antenna. The tightening torque of the nut: 1.35 Nm
(min) – 1.5 Nm (max).
5. Protect the connectors from environmental influences (e.g. with self-
vulcanizing adhesive tape or a shrink-on sleeve).
U-bolt, Thread:
5
/
'' –
16
18 UNC - 2A
L- bracket
Washer, Thread:
/
'''
5
16
Spring washer, Thread:
5
/
Hexagon nut, wrench size:
Thread:
5
/
''- 18, thickness
16
''
16
1
/
'',
2
17
/
''
64
Werbung
