Installation - Negri R95EHP4 Handbuch

NEGRI GARDEN EQUIPMENT
1 INTRODUCTION
This instruction manual must be considered as a part of the machine. The suppliers of both new and old machines must prove through documentations that the present manual
has been delivered with the machine.
THE OPERATOR MUST READ THIS INSTRUCTION MANUAL AND ALL ITS SECTIONS CAREFULLY, BEFORE PERFORMING ANY KIND OF OPERATION ON THE
MACHINE.
2 MACHINE USE
The R95 bio-shredder is a machine used to shred in small pieces any kind of vegetable waste.
The machine is provided with a cutting group of blades and hammers, has a high production and a large and practical hopper. These features make the machine suitable for a
hobby use.
3 SAFETY INSTRUCTIONS
During start up, use and maintenance of the machine, the following safety rules must be observed:
3.1 O '
PERATOR S SAFETY
Under-sixteen years old are not allowed to use bio-shredders.
During the machine use, the user is responsible against third parties.
During the grinding, it is compulsory to wear gloves and protective spectacles; it has been proved that, with a constant use of the machine, the sound level allowed is exceeded;
it is highly recommended to wear an ear protector.
During the use of the machine, it is necessary to wear stout shoes and long trousers all the time.
Hair must be tied above the shoulders.
Do not use the machine, if you are tired, ill, or after having ingested alcoholic drinks, medicines or drugs.
Never start up the machine indoor. Exhaust gasses are lethal.
Never use stools, ladders, etc. to reach for the cutting assembly at the end of the hopper, if the machine is not turned off.
3.2 M
ACHINE SAFETY
During the start up of the engine, make sure all the parts of the machine have been perfectly mounted in a correct way.
Before using the bio-shredder, replace broken or damaged parts.
The machine must be placed on a flat and resistant base.
Before leaving the bio-shredder, turn the engine off, according to the manual instructions.
If the machine is provided with an electric motor, switch it off, and pull out the plug from the power grid. Bio-shredders having an electric motor can be connected to the grid only
by means of a socket provided with an automatic protection switch. According to the regulations En 60204-1, for the connection lines, only rubber cables or cables marked
H05RN-F can be used. It is important to highlight that the joints to be used for connection lines must be protected against water splashes.
It is compulsory to use the machine with all its safety devices mounted correctly.
Do not put any material into the bio-shredder before having turned on and brought to is maximum speed the engine.
Do not ever modify the machine.
Do not use the machine for functions others than those for which it has been conceived.
3.3 S
AFETY DURING GRINDING
During the use of the bio-shredder, the operator must wear individual protective devices, always stay close to the hopper where he introduces the material to be grinded, and
make sure that nobody is within a 20 meters radius.
It is forbidden to introduce branches whose dimensions exceed those prescribed (70 mm as indicated by the pictogram on the hopper) .
Do not introduce in the bio-shredder stones, metal, glass, plastic, earth, packs of newspapers, ect. But only vegetable waste.
When the machine is working, do not ever remove any protective guard
The operator must never be close to the discharge pipe of the material, while the machine is working.
Do not put any body part inside the protective guards.
When the motor is working, no body part must be close to the silencer.
3.4 S
AFETY WHEN USING FUEL
It is forbidden to smoke in the vicinity of the machine during refueling.
Turn the engine off before removing the cap of the tank.
Before refuelling, wait for the silencer to cool down (as it is placed next to the tank).
Remove any possible fuel leaks before starting up the engine.
Before turning the machine on, move it for at least 3 meters from the zone of refueling.
3.5 S
AFETY OF MAINTENANCE
For any maintenance activity of the machine, please refer to the procedures indicated in the section Maintenance.
Use original spare parts only.
While replacing the blade and cleaning the machine, be careful not to cut yourselves: "CUTTING TOOLS ARE DANGEROUS".
Do not perform any kind of maintenance activity before having worn protective gloves and safety shoes, and having turned off the engine: wait for the rotor to have completely
stopped.
3.6 S
AFETY OF TRANSPORT AND STORAGE
Make sure all parts of the shredder are perfectly fixed to the machine, in order to avoid losing any objects during transport.
Transport the machine carefully and with the motor turned off.
Use the special hook to lift the machine (see Transport paragraph).
Drain the tank before storing the machine.
4

INSTALLATION

The R95 bio-shredder is usually provided with some parts that still need to be mounted, for packing or delivery reasons. Wear the gloves and carry out the following operations by
referring to the drawings in the first pages of this handbook.
4.1 INSTALLATION OF THE R95
Screw the feet in rubber (D04020) with washers (RP8Z) and nuts (M8AUTZ) to the back feet (R095005). Then screw the back feet to the bedplate of the machine with the
screws (V825Z), the washers (RP825Z and RP8Z) and nuts (M8AUTZ). Pic. 1A
Mount the wheels (NGR0566A) on the axle, blocking them with the specific washers (RDFP20). Pic. 1B.
Position the discharge pipe (R095035) on the body of the machine and fasten it with the nuts (M8AUTZ) and washers (RP8Z). Pic. 1C
Mount the hopper (R095009) on the body of the machine as shown in the picture. Once the hopper has been fastened with the nuts (M8AUTZF), screw the magnetic knob
(NGR0565A) till its end. Screw the handle (M443/140N) on the hopper, fasten it using the screws (V825TCEIZ), the washers (RP8Z) and the nuts (M8AUTZ). Pic. 1D.
R95 B-E
15