Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
2.3
Mode and menu
2.3.1 Normal mode of the COM-ON-AIR
®
COM-ON-AIR
P L U G is not synchronised
®
COM-ON-AIR
P L U G is synchronised
®
COM-ON-AIR
P L U G is in communication
®
2.3.2 Programming mode (see brief operating instructions p. 13)
To enter the programming mode it is necessary to plug a wired phone on the
P L U G.
COM-ON-AIR
®
• Pick up the line
• Connect the COM-ON-AIR
P L U G to power supply to reactivate interface.
®
The LED flashes quickly and a beep every second is emitted in the handset.
• Dial # to enter programming mode. You can hear 2 beeps per second.
At any time, you can cancel your programming and return to the initial menu by dialling *
If you hang up the telephone before the end of the procedure of synchronisation,
COM-ON-AIR
P L U G goes back in normal mode.
®
If no manipulation was done during one minute, the COM-ON-AIR
back in normal mode.
2.3.3 Synchronisation menu (see brief operating instructions p. 13)
• Enter in Programming mode (see 2.3.2)
• Dial 1 to enter this menu. 3 beeps per second can be heard in the handset.
• Put the basestation in subscription mode.
• Select the base number: 1, 2, 3 or 4. 2 beeps: the code was accepted
Or 1 long negative beep: an error was made.
• Enter the base PIN code. To know this code, have a look on the user manual of the basestation
(default code: 1111)
• Dial # to confirm. Quick search beep can be heard until:
2 beeps: the synchronisation is accepted
Or 1 long beep:
COM-ON-AIR
you return in programming mode (1 beep per second).
2.3.4 Setting the speaker volume menu (see brief operating instructions p. 13)
• Enter in Programming mode (see 2.3.2)
• Dial 2 to enter this menu. 3 beeps per second can be heard in the handset.
• The sound level is programmed on 5 buttons:
weakest level and
the highest.
• Dial # to confirm your choice.
P L U G
The green LED illuminates for half of a second.
The green LED illuminates 1/10
th
of a second.
The green LED illuminates permanent.
®
P L U G goes
®
P L U G is not synchronised. In that case,
Knowing
corresponds to the
corresponds to the level by default.
10
2.3.5 Change basestation menu (see brief operating instructions p. 13)
• Enter in Programming mode (see 2.3.2)
• Dial 3 to enter this menu. 3 beeps per second can be heard in the handset.
• Dial the base number of the one you wish to use. (between 1 and 4)
• Dial # to confirm
2.3.6 Default settings menu (see brief operating instructions p. 13)
• Enter in Programming mode (see 2.3.2)
• Dial 0 to enter this menu. 3 beeps per second can be heard in the handset
• Dial # to confirm. A beep can be heard to confirm the use of default settings.
3
Use of the phone
Remarks: COM-ON-AIR
P L U G does not interfere with the functions of your telephone:
®
answering machine, directory...
4
Use of several COM-ON-AIR
Several COM-ON-AIR
®
P L U G or handsets can be declared and used on your base. By mixing
various devices, you can benefit from the simultaneity of external and internal communications.
5
Technical characteristics
Standards:
DECT ( Digital Enhanced Cordless Tele-communication)
Frequency ranges:
1880 Mhz in 1900 MHz
Modulation:
GFSK
Vocal coding:
32 kbit / s ADPCM
Use telefax:
group maximum 3, V.29 with 9600 bit/s
Power of broadcast:
10mW, average power
Reach:
300 m maximum in outside, 50 m in inside
Power supply:
220 / 230V ~/50 Hz
Consumption:
4 VA
Surrounding conditions
authorised for the
exploitation (maximum):
From – 5°C to 55°C
Between 20 % and 75 % of relative humidity
Temperature of stocking
authorised:
-10°C in +60°C
Type of numbering:
DC / MF
Reminder of recorder:
flashing
Dimensions:
62 x 119 x 31 mm (l x L x h)
Weight:
approximately 65 grams
Length of the cordon:
about 3 m
Index card of connecting: block of connecting sector
®
P L U G
11
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
Fehlerbehebung
