Changing The Opening Direction Of The Doors - SNAIGE CD290-1004 Betriebsanleitung

• Protect the appliance inner surfaces and plastic parts from fats, acids and sauces.
• Regularly clean the hermetic gaskets of the doors. Wipe dry.
• REGULARLY CLEAN THE THAW WATER CHANNEL SPACE WITH A SPECIAL
• At least once a year clean dust away from the back part of the appliance body
• DO NOT use detergents containing abrasive particles, acid, alcohol or benzene for cleaning the
appliance inner and outer surfaces. DO NOT use for cleaning cloths or sponges that have coarse
surfaces intended for scrubbing. Outer of the doors – glass – clean with agents intended for glass
cleaning.
• If the appliance is to be left switched off for an extended period, leave its doors open.

CHANGING THE OPENING DIRECTION OF THE DOORS

It is recommended that changing the opening direction of the doors should be done with a helper.
You will need two spanners No. 8 and No. 10 and a Philips head screwdriver.
When changing the opening direction of the doors YOU CAN NOT lay the refrigerator horizontally!
Do the actions below in the order they are listed:
FOR THE MODELS WITH ONE DOOR (see fig. 3, page 2):
1. Turn off the appliance and pull the plug out of the electricity supply socket
2. Unscrew two screws 7 and remove the bottom bracket 8 together with the set of washers 6 on
the axle and the spacer 5.
3. Unscrew two screws 7 and remove the bracket 11. Remove the door 4.
4. Unscrew the axle 2 together with the nut 1 and washers 3 from the upper bracket and screw all
this set on the reverse side of the door;
5. Before hanging the door, turn the door over by 180
6. Unscrew fixing screws 12 from doors, remove handles 13 and fix them screwing in free holes on
the same side. Plate 10 remains in its place.
7. Before screwing the bottom bracket 8 together with the set of washers and spacers on the
reverse side of a cabinet, insert the bracket axle to the door.
8. Screw the bracket 11 on the reverse side of a cabinet.
FOR THE MODELS WITH TWO DOORS (see fig. 3, page 2):
1. Turn off the appliance and pull the plug out of the electricity supply socket.
2. Unscrew two screws 12 and remove the bottom bracket 13 together with the set of washers 11
on the axle and the spacer 10.
3. Unscrew two screws 12 and remove the bracket 15. Remove the bottom door 9.
4. Unscrew fixing screws 7 of the middle bracket. Remove the middle bracket 6 together with
washers on the axle and the spacer 5. Remove the top door 4.
5. Unscrew the axle 2 together with the nut 1 and washers 3 from the upper bracket and screw all
this set on the reverse side of the door.
6. Take out the plugs 18 in the crossbar zone and displace them on the reverse side.
7. Before hanging the upper door, turn the door over by 180
Before screwing the middle bracket 6 with the set of washers and spacers on the reverse side of
the cabinet, insert the bracket axle into the upper door;
8. Before hanging the bottom door on the middle bracket axle, turn them over by 180
9. Unscrew fixing screws 16 from both of door, remove handles 17 and fix them screwing in free
holes on the same side. Plate 14 remains in its place.
10. Before screwing the bottom bracket 13 together with the set of washers and spacers on the
reverse side of a cabinet, insert the bracket axle to the door.
11. Screw the bracket 15 on the reverse side of a cabinet.
In case of accidental spills – immediately clean with warm soapy water or
dishwashing detergent. Wipe dry.
CLEANER 8 FOR THAT PURPOSE (Fig. 1).
and the compressor. A soft brush, electrostatic cloth or vacuum cleaner may be
used for cleaning.
0
and insert the upper axle in the door.
0
and insert the upper axle in the door.
7
0
.