Radio Frequency Notes; Operation Of Earphones; Charging The Battery; Bluetooth Connection Build Up - Inline pure mobile Bedienungsanleitung

www.inline-info.com

7. RADIO FREQUENCY NOTES

General Allocation of Frequencies for Use in Local Net-
works; Wireless Local Area Networks (WLAN Radio Ap-
plications)
Based on § 55 of the German Telecommunications Act
(Telekommunikationsgesetz - TKG) we herewith assign
frequencies in the range 2400.0 – 2483.5 MHz for use of
the general public in local networks, Wireless Local Area
Networks (WLAN Radio Applications). With this General
Allocation, we fulfil the compulsive implementation of
the Decision by the European Commission on Harmo-
nisation of the Radio Spectrum for Use by Short-Range
Devices dated 2006/11/09 (2006/771/EG), as amended
by implementing the decision of the Commission da-
ted 2011/12/08 (2011/829/EU), published in the Official
Journal of the European Union L 329, page 10 ff. dated
2011/12/13 in Germany.
If you intend to use this product outside of Germany,
please read up in advance on the respective regulations
in your host country.

8. OPERATION OF EARPHONES

a. Charging the battery
Before using the headset for the first time, the built-in bat-
tery must first be charged. Use the included micro USB
cable.
1. Connect the micro USB connector to the USB
port of your headphone.
2. Connect the USB-A plug to a free USB port on
your computer or use another USB power source.
3. The full charge takes about 1.5 hours. The active
charging process is indicated by a red LED on the
control element. After successful charging, the
LED turns to blue and you can disconnect.
4. After switching on, different acoustic signals will
sound. „Battery high" sounds at a charge of 100
to about 70%, „Battery medium" at about 70-
50%, „Battery low" is when reaching a low battery
level from about 30% remaining capacity Repeat
steps 1-3 to recharge the headphones.
NOTE!
Please note that the charging time may
vary depending on the output power of
the USB power source.
10
NOTE!
If you're using a spare USB port on your
computer for charging, make sure your
computer is turned on and not in sleep
mode.
TIP!
To charge the battery, we recommend
the InLine® USB power supplies such
as InLine® USB power supply 2-fold,
charger, power adapter, 100-240V to
5V / 2.1A, available in black (Article 31505S) and white
(Article 31505W).
b. Bluetooth connection build up
You can establish a wireless connection between a play-
er and the headset via Bluetooth. For this, the playback
device must have a Bluetooth function and it must be
switched on.
1. Put the headset in pairing mode. Hold down the
multifunction button for approx. 5 seconds. First
you will hear the message „Power On", shortly
afterwards „Pairing" will sound. An alternating
flashing of the LED in red and blue signals that
the headset is ready for connection.
2. Open the Bluetooth settings of your playback de-
vice and search for available devices. Make sure
your desired Bluetooth device is no more than
one meter away from your headphones. Please
also note the instructions in the operating instruc-
tions of your Bluetooth playback device or con-
tact the manufacturer if you have any questions.
3. Select the device InLine PURE mobile ANC on
your Bluetooth device to establish the connec-
tion.
4. The successful connection is signaled by a short
two flashes of the LED in blue at a distance of
about 2 seconds and the acoustic feedback
„Your device is connected" sounds in the head-
phone. Once paired devices are remembered and
connect automatically as soon as the PURE mo-
bile is switched on (power on).
NOTE!
If pairing is not possible, turn the head-
phones off and on again first and try
connecting again.