Grundig RR 630 CD Serviceanleitung Seite 5

Operating Instructions
Note: This chapter contains excerpts from the operating instructions. For further particulars please refer to the
appropriate user instructions the part number of which is indicated in the relevant spare parts list.
CONTROLS
ANTENNA
SCALE
FUNCTION
FM
MW LW
U.B.S.
VOL
VOLUME
ON 6
F-SKIP
ON STOP
PROG
R-SKIP
REPEAT PLAY/
PAUSE
TRACK
TAPE DIRECTION
CASSETTE
Top and front panel
ON 6 – lights up when the unit is on
p
– connection for headphones
VOLUME – to adjust the volume
UBS – to switch the U B S on and off
LTRA ASS YSTEM
FUNCTION – CD: to switch to CD mode / Power On
– TAPE/OFF: to switch to TAPE mode / Power Off
– RADIO: to switch to RADIO mode / Power On
ANTENNA – telescopic aerial for FM reception
SCALE – tuning dial scale
BAND – to select between FM, MW, and LW waveband
TUNING – to tune to a radio station
FM STEREO 6 – lights up when receiving FM stereo stations
OPEN/CLOSE – to open and close the CD door
REMOTE SENSOR – to receive the remote signals (only RR 660 CD)
CD PLAYER
Playing a CD
• Press PLAY/PAUSE 2; to start playback.
– The PLAY/PAUSE 6 indicator will light up and the display
shows the track number.
• Adjust the sound using the VOLUME and UBS controls.
• For brief interruptions, press PLAY/PAUSE 2;.
– The PLAY/PAUSE 6 indicator starts blinking
• To resume playback, press PLAY/PAUSE 2; again.
• To stop playback, press STOP 9.
– The total number of tracks will appear on the display.
– The CD player also goes to position STOP:
– when the end of the CD is reached;
– if the batteries run down or if the power supply is interrupted.
• To take out the CD, open the CD door by pressing
OPEN/CLOSE.
• Open the CD door only if the CD-player is in position STOP.
Selecting another track during play
• Press R-SKIP Q or F-SKIP R several times until the
required track number appears in the display.
– The selected track begins to play.
Starting with a particular track
• Press R-SKIP Q or F-SKIP R until the required track
number appears in the display.
– Play starts automatically from the selected track.
Searching for a passage during play
• Hold R-SKIP Q down to search backwards to the
beginning.
• Hold F-SKIP R down to search forwards to the end.
Note: This function can be described as "audibly" searching for a
title. During the search, volume is reduced and returns to its
adjusted level as soon as the button is released.
CD Control
R-SKIP Q – to skip and search backward
F-SKIP R – to skip and search forward
BAND
TUNING REPEAT – to repeat one/all tracks
FM STEREO 6
STOP 9 – to stop playback
PLAY/PAUSE 2; – to start and interrupt playback
OPEN/CLOSE
PROG. – to programme track numbers
in the memory
CD
REPEAT 6 – lights up when repeat one
REMOTE SENSOR
function is on, blinks when
repeat all function is on.
PLAY/PAUSE 6
– lights up during CD
playback, blinks during CD
pause mode.
Cassette Control
0
– to start recording
B
– to start cassette playback
Q
– fast rewind
R
– fast forward
9//
– to stop and eject the cassette
;
– to interrupt/continue
playback/recording
Back panel
Battery compartment: – for inserting 8 batteries
type R20, UM1 or D-cells.
AC ~
– Socket for mains lead.
Repeat function
Repeating a track
• Press REPEAT before or during playback.
– The REPEAT 6 indicator lights up.
– The track will now be repeated continuously
• Press REPEAT twice to stop the track being
repeated.
Repeating the CD
• Press REPEAT twice before or during
playback.
– The REPEAT 6 indicator starts blinking.
– The CD will now be repeated continuously
• To switch the repeat mode off, press REPEAT
again.
Random function
(only RR 660 CD via remote control)
• During playback, press the MODE button on
the remote control three times .
– The tracks are played in random order until all
of them have been played once.
– The display indication toggles between the
track number and a moving symbol.
• The function is deactivated by pressing
STOP 9 (in which case the CD stops) or
MODE again; in this case the remaining tracks
are played in their normal order.
• The random function is not possible during
playback of a programme.
RADIO
Radio aerials CD handling
– For FM, pull out the telescopic aerial. To im-
• Use only Digital Audio CDs which have the symbol
prove FM-reception, incline and turn the aerial.
• To take the CD out of its box easily, press the centre spindle while lifting
Reduce its length if the FM-signal is too strong
the CD.
(very close to a transmitter).
• Never write on a CD or attach any sticker to the CD.
– For MW/LW, the set is provided with a built-in
aerial, so the telescopic aerial is not needed.
• Always hold the CD at the edge and always store it in its box after use
Direct the aerial by turning the whole set.
with the label facing up.
• To remove dust and dirt, breathe on the CD and wipe it with a soft, lint-
Radio reception
free cloth in a straight line from the center towards the edge. Cleaning
• Set the FUNCTION switch to RADIO. agents may damage the CD.
– The ON indicator 6 lights up.
• Do not expose the CD to rain, moisture, sand, or to excessive heat. (E.g.
• Adjust the sound using the VOLUME and UBS from heating equipment or in motor cars parked in the sun).
controls.
• You may connect stereo headphones having a
3.5 mm plug to the jack p .
– Inserting the plug will disconnect the speakers.
Warning
• Select the wave band using the BAND
CLASS 1 LASER PRODUCT means that the laser´s construction makes it
selector.
inherently safe so that the legally prescribed maximum permissible ratiation
• Tune to a desired radio station using the
values can never be exceeded.
TUNING control.
CAUTION: Using any equipment or devices other than those described and
6
– When the indicator FM STEREO appears,
specified in these operating instructions, or tampering with the unit in any
you are receiving an FM stereo transmitter.
way, can result in dangerous exposure to radiation.
• The set is switched off when the FUNCTION
switch is in the TAPE/OFF position and no
Inserting a CD
buttons are pressed.
• Set the FUNCTION switch to CD.
–The ON indicator 6 goes out.
– The ON indicator 6
lights up.
• Press OPEN/CLOSE to open the CD door.
• Insert the AUDIO CD, printed side facing up.
• Close the cover.
– The CD-player scans the contents list of the CD.
After that, the total number of tracks appears on the display.
CASSETTE DECK
Compact cassettes
Cassette playback
– Copyright: Recording is permissible insofar
• Set the FUNCTION switch to TAPE/OFF.
copyright or other rights of third parties are
• Press 9// to open the cassette holder.
not infringed.
• Insert a recorded cassette.
• For recording, use a NORMAL (IEC type I)
with the open side
cassette on which the tabs are not broken
downward and the full
out.
spool on the left.
– This deck is not suited for recording on
• Adjust the sound using the
CHROME (IEC II) or METAL (IEC IV)
VOLUME and UBS
cassettes.
controls.
• For playback, any cassette type may be in-
• You may connect stereo headphones having a
serted.
3.5 mm plug to the jack p
– At the very beginning and end of the tape,
– Inserting the plug will disconnect the speakers.
no recording will take place during the
• Press B and playback will start.
7 seconds when the leader tape passes the
– Playback stops when the tape in the deck
recorder heads.
reaches the end.
• To prevent the acciden-
• For brief interruptions, press
– To restart playback, press this button once
tal erasure of a recor-
more.
ding, keep the
1 • To stop, press 9//.
cassette side to be
safeguarded in – When the end of the tape is reached the B
front of you and
button is released.
break out the left
– The set will be switched off if the FUNCTION
tab. Now, recording on this side is no
switch is in position TAPE/OFF and no
longer possible.
buttons are pressed.
– The ON indicator 6 goes out.
• To render this safeguard ineffective, cover
the hole with a piece of adhesive tape.
Winding the tape
• Do not expose the cassettes to rain,
• Press R to search forward to the end of the
moisture, sand, or to excessive heat. (E.g.
tape.
from heating equipment or in motor cars
• Press Q to search backward to the
parked in the sun).
beginning of the tape.
• Do not store cassettes near strong magnetic
• To stop, press 9//.
fields (for example, TV sets, speakers,
engines, etc.).
CD PLAYER
.
2
1
CLASS 1
LASER PRODUCT
Cassette recording
• Press 9// to open the cassette holder.
• Insert the cassette.
• When monitoring during record-
ing, adjust the sound using the
controls VOLUME and UBS.
These controls do not affect the
recording.
• Start recording by pressing 0.
(the B button is automatically also pressed).
– When the end of the tape is reached, the recorder
buttons are released.
.
;
• To interrupt recording, press .
;
• To continue recording, press again.
• Press 9// if you want to stop recording before the
end of the tape.
On pressing again, the cassette holder will open.
;
. • The set is switched off if the FUNCTION switch is in
position TAPE/OFF and no buttons are pressed.
6
– The ON indicator goes out.
Recording from the CD-player (CD synchro recording)
• Set the FUNCTION switch to CD.
• It's not necessary to start the CD player separately: by
pressing 0 the CD player starts automatically.
– If the CD player is in STOP position, recording will
start from the beginning of the CD (or from the
beginning of the programmed selection).
• To start a recording in the middle of a track, play the
CD in the normal way.
• As soon as the desired passage is reached, pause the
CD and then start recording by pressing 0.
Recording from the radio
• Set the FUNCTION selector to RADIO.
• Select the wave band using the BAND switch.
• Tune to desired radio station using the TUNING
control knob.
• Start recording by pressing 0.