Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Stroke counter
The tool is equipped with capability for cali-
bration. This is accomplished by measuring
(weighing) grease flow output and dividing
the weight of grease by number of strokes.
Simply put your thumb on the stroke counter
button, Fig. 1 during operation of the tool and
count.
Some OEM's are recommending the exact
amount of grease to lubricate critical bear-
ings. By counting the strokes you will know
how much grease has been dispensed to
lubricate the bearing. Here is the table of the
grease output vs. number of strokes.
Stroke count
10
15
20
Note: Lincoln is recommending this feature
only on low output/high pressure mode.
PERSONAL SAFETY
1.
Always wear eye protection. The Power-
Luber can generate up to 7,000 psi (476
bar).
2.
Use only Lincoln 1218, 1224, 1230 or
1236 outlet whip hoses. Grease injection
injuries are a very serious injury. Hold
the hose only in the area of the spring
guard.
3.
Avoid accidental starting. Be sure switch
is not depressed when inserting battery
pack.
4.
Do not bend the hose so that it becomes
kinked.
5.
Replace the hose at the first sign of wear,
kink or damage to the outside jacket.
USE AND CARE
1.
Do not continue to hold down trigger if
grease gun is stalled. This could damage
the motor or cause fire.
2.
When battery pack is not in use, keep it
away from other metal objects like: paper
clips, coins, keys, nails, screws, or other
small metal objects that can make a
connection from one terminal to another.
Shorting battery terminals together may
cause sparks, burns, or a fire.
3.
Use only accessories that are recom-
mended for use with the Lincoln Power-
Luber. This tool is a fully rated portable
power lubrication product, only acces-
sories that are capable of handling 7,000
psi (476 bar) should be used.
Form 402103
Model 1400, 1440, 1442, 1442E, 1444, 1444E
Output/stroke
oz.
gram
0.20
5.7
0.30
8.5
0.40 11.4
PowerLuber Grease Gun
SERVICE
1.
Service must be performed only by qualified
repair personnel. Service or maintenance
performed by unqualified personnel may
result in a risk of injury.
2.
When servicing a PowerLuber, use only Lin-
coln replacement parts. Use of unauthorized
parts may create risk of injury and will void
the warranty.
INSPECTION
Visually inspect for damaged, loose or missing
parts. If equipment is worn or damaged, remove
from service. Contact an authorized service
center for damage assessment or repair.
OPERATION
Prime the PowerLuber after each refill or grease
cartridge change. Prime the gun before using it
to lubricate grease points.
To prime, operate the gun until grease flows from
the hose. Use vent valve (Figure 1, page 3) to
expel air pockets.
Air pockets in the cartridge lubricant will
cause the gun to lose its prime.
Removing Empty Grease Cartridge
1.
Pull back on the follower handle until the
follower rod is fully extended and latch the
follower rod groove into the slot on the tube
cap.
2.
Unscrew the grease tube assembly from the
PowerLuber.
3.
Carefully release the follower handle to eject
the empty cartridge from container tube.
I
nstalling Grease Cartridge
1.
Visually check the follower seal lip direction
before loading a new cartridge. The follower
seal lip must be directed toward the follower
handle or rear side for cartridge loading.
See Fig. 2. To change the direction of the
follower seal, unscrew tube cap from grease
tube assembly and pull on the handle to
remove follower seal from tube. Flip follower
seal over and re-assemble.
2.
Pull back on the follower handle and latch
the follower rod groove into the slot on the
tube cap.
3.
Remove the plastic cap from the grease car-
tridge and insert cartridge into the container
tube.
Page Number - 5
Werbung
Inhaltsverzeichnis
Fehlerbehebung
