Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Philips AVENT Microwave Steam Steriliser
GB
Thank you for
choosing Philips AVENT
Now you can enjoy the convenience
and ease of using the Philips AVENT
Microwave Steam Steriliser, which
effectively eliminates harmful
bacteria in just minutes! Its large
capacity holds more than any other
microwave steriliser – up to six
bottles – yet it is compact and
lightweight enough for travel.
Advanced features such as cool
safety grips aid in safe handling,
and make it easier than ever to
sterilise Philips AVENT Breast
Pumps, Bottles, Cups and more.
Please take a few minutes to read through
the ENTIRE INSTRUCTION LEAFLET including
the warnings before using your Microwave
Steam Steriliser for the first time. PLEASE
RETAIN THESE INSTRUCTIONS. Also available
at www.philips.com/AVENT
Loading the steriliser
Before using the Microwave Steam Steriliser, always
ensure that the items are positioned according to the
below loading instructions.
A
Loading six 125ml/4oz or 260ml/9oz
AVENT Feeding Bottles
1. Position the teats in the teat cavities around
the dome cap stem.
2. Place the screw rings over the teats.
3. Place the first three dome caps in the lower slots
of the dome cap stem.
4. Place the remaining three dome caps in the upper
slots of the dome cap stem.
5. Position the bottles upside down around the
previously loaded teats and screw rings.
B
Loading three 330ml AVENT Feeding Bottles
1. Position the teats in the three teat cavities
surrounding the dome cap stem.
2. Place the screw rings over the teats.
3. Position the bottles upside down in the three
outer teat cavities.
4. Arrange the three dome caps around the edge
of the rack in between the inverted bottles.
8
Assembly and Use
Contents
I
1. Lid
a. Clips
2. Bottle/Accessories Rack
b. Dome cap stem
c. Bottle cavity
d. Teat cavity
e. Breast Pump slots
3. Base
f. Safety grips
Before each use
II
Wash all items in warm
soapy water and then
rinse in water.
1. Remove rack from the
steriliser and pour
200ml of water
into the base.
Loading one or two Philips AVENT Breast
C
Pumps (non-electrical components only) and
two 125ml/4oz OR two 260ml/9oz AVENT
Feeding Bottles
1. Disassemble the Breast Pump ensuring
the stem is removed from the diaphragm.
2. Position the Breast Pump bodies into the
two slots provided.
3. Position the teats in the teat cavities around
the dome cap stem.
4. Place the screw rings over the teats.
5. Place one dome cap in the unobstructed lower
slot of the dome cap stem, then the second in
the upper slot on top of the inserted dome cap.
6. Position the bottles upside down in the
unobstructed bottle cavities.
7. Place the remaining NON-ELECTRICAL pump
components in any unobstructed space on the rack.
Loading six 180ml/6oz OR 240ml/8oz
D
AVENT VIA Cups and Lids
1. Position the VIA Cups upside down around
the dome cap stem.
2. Position the VIA Lids vertically around the racks
edge. Rims should face out for easier loading.
IMPORTANT: Failure to add
enough water may cause
damage to the Microwave
Steam Steriliser and/or your
microwave. Adding too much
water may mean your items are
not properly sterilised.
2. Put the rack back into
the base.
3. Position the lid over the
steriliser base and lock the
clips into place until you
hear them "click".
4. Ensure that the microwave
is clean and dry before use
– Place the steriliser into the
centre of the microwave.
Select microwave wattage
III
and timings – See Table III
– do not exceed these times.
Werbung
