Mixing Fuel - EINHELL MS 24 Bedienungsanleitung

Anleitung_MS 24 _ MSB 24
• "U¨ HANDLE INSTALLATION (MS 24) (Fig 1b)
1. To install handle onto unit, you will need the
following components from your user kit: "U"
handle (A), fixing holder (B), clamp (C) and
screws (D).
2. Install the fixing holder (B) on the shaft around 4"
(10-12cm) away from the and of the grip, put the
clamp (C) and tighten the 2 screws (D).
3. Install the U handle (A) on the fixing holder, put
the other clamp (C) and tighten the other 2
screws (D).
4. Install wire tie (E) included in the user kit as
shown (Fig. 1D).
• BLADE GUARD INSTALLATION (Fig 2a-2b)
1. Remove gear collar (A) from the threaded gear
housing shaft.
2. Place the shield on the gear housing and align
the mounting holes. Insert screws (B) as shown in
illustration and tighten securely.
3. Reinstall the gear collar (A). Ensure the collar
spacer (C) is in place or the collar will rub the
gear housing.
• STRINGHEAD INSTALLATION (MS 24)
(fig 3a-3c)
1. Install gear collar (A) ensuring that collar spacer
(B) is in place.
2. Insert holding pin (C) and thread stringhead onto
shaft. Tighten stringhead by hand only
• DEBRIS SHIELD SKIRT INSTALLATION
Turn the unit over and install the debris shield skirt
(A) as shown (Fig. 4A)
CAUTION: Skirt must be installed to properly
dispense cutter line and protect operator
• BLADE INSTALLATION
CAUTION: NEVER use unit if blade is warped or
has teeth that are chipped or missing. Replace a
damaged blade immediately.
CAUTION: NEVER operate unit with a blade
unless metal blade guard is properly installed.
NEVER operate a unit with a damaged guard.
CAUTION: Always wear heavy-duty work gloves
when handling and installing a blade.
1. To install the blade you will need the items
illustrated (screwdriver not provided): holding pin
20.12.2002 9:40 Uhr
2. Remove three screws (H). Remove the skirt (A).
3. Leave the holding pin (B) in place.
properly sized to the collar arbor.
4. Install blade (D) with teeth pointing CLOCKWISE
5. Install flange (F) with FLAT SURFACE facing
NOTE: Make sure blade is centered on collar arbor.
6. Tighten nut (C) securely by turning it
Fuel and lubrication
•
Use regular grade unleaded gasoline mixed with
Talon 25:1 custom 2-cycle engine oil for best results.
Use mixing ratios in FUEL MIXING TABLE.
unit. This will cause permanent engine damage and
void the manufacturer's warranty for that product.
Never use a fuel mixture that has been stored for
over 90 days.
a recommended mixing ratio of 100:1. If insufficient
lubrication is the cause of engine damage, it voids
the manufacturer's engine

• MIXING FUEL

Add the oil to an approved fuel container followed by
the gasoline to allow incoming gasoline to mix with
oil. Shake the container to ensure thorough mix.
warranty. Gasolilne and oil must be mixed at 40:1.
•
Gasoline
5 Liters
Mixing Procedure
Seite 21
(B), retaining nut (C), blade (D), screwdriver (E),
flange (F), socket wrench (G)
Use the holding pin to prevent the collar from
turning while removing the stringhead (turn
CLOCKWISE) (Fig. 5B).
Warning: Be sure the blade center hole is
as shown in the illustration (Fig. 6C).
blade (Fig. 5C).
COUNTERCLOCKWISE with socket wrench (G).
Remove holding pin (Fig. 5D).
Fuel
Warning: Never use straight gasoline in your
Warning: Do not use any 2-cycle oil product with
warranty.
Warning: Lack of lubrication voids engine
Fuel Mixing Table
Lubricant
200 ml (cc)
25 Parts Gasoline to
1 part Lubricant
1 ml = 1 cc
GB
21