Mitsubishi Electric Lossnay LGH-200RVXT-E Installationsanleitung Seite 15

Function settings (continued)
No Function
Filter maintenance and fan power up setting
*1
against filter choking
2 Lossnay core maintenance indicator setting
5 Automatic recovery setting after power interruption
6 Indoor negative pressure setting
7 Indoor positive pressure setting
8 Max. fan speed setting during the first 30 minutes
9 Delay start setting for air conditioner starting
13 Exhaust fan setting during air conditioner defrosting
Exhaust fan setting at OA temperature lower
14
than -15 ˚C
15 Interlock mode setting
28 Pulse input setting
Night-purge setting 1)
*30
Air volume
Night-purge setting 2)
*31
Outdoor and indoor temperature gap
Night-purge setting 3)
*32
Threshold of outdoor temperature
Night-purge setting 4)
*33
Time span for memorizing
*34 Input priority setting
36 Outdoor temperature display setting
37 Indoor temperature display setting
38 Calculated supply air temperature display setting
39 Temperature exchange efficiency setting (10 digit) Setting Data 0 to 9 -- > 10 digit of temperature exchange efficiency 0 to 9
40 Temperature exchange efficiency setting (1 digit) Setting Data 0 to 9 -- > 1 digit of temperature exchange efficiency 0 to 9
*41 Outdoor temperature correction
*42 Indoor temperature correction
*51 Automatic ventilation mode setting
Automatic ventilation mode setting 1)
*52
Outdoor and indoor temperature gap
Automatic ventilation mode setting 2)
*53
The lowest outdoor temperature setting
Automatic ventilation mode setting 3)
*54
The lowest indoor temperature setting
*55 Supply fan power up setting
*56 Exhaust fan power up setting
Operation monitor output synchronized with
57
exhaust fan or supply fan
By-pass monitor output or Pre-heater output set-
58
ting
Pre-heater setting 1)
*59
ON temperature
Pre-heater setting 2)
*60
OFF interval
*61 Fan speed for air volume "High" input
*62 Fan speed for air volume "Low" input
*63 External fan speed input setting (0 - 10 VDC)
100 Initialization
This table shows the summary of function settings. Please refer to the following pages for more details.
The functions indicated with * are newly added or modified from Lossnay LGH-RX
The functions indicated with "N/A" in the "DIP-SW No." column are available only when using with remote controller PZ-61DR-E.
Eng-14
0 1 2
Indicator
Indicator N/A
Dip-SW available
Fan power
priority Fan power
up N/A
up N/A
N/A Available -
Stop when Start when
Dip-SW
the power the power
priority
is On is On
Dip-SW Supply 1
N/A
priority down
Dip-SW Exhaust 1
N/A
priority down
N/A Available -
Dip-SW
N/A 15 min
priority
Dip-SW
Stop No change
priority
Dip-SW Fan speed
Stop
priority 1 or 2
Dip-SW ON/OFF ON inter-
priority interlock lock
Dip-SW Non-pulse Pulse
priority input input
N/A Fan speed 1 Fan speed 2 Fan speed 3 Fan speed 4
0 ˚C 1 ˚C 2 ˚C
Setting Data 0 to 15 -- > The lowest outdoor temperature for Night-purge 15 ˚C to 30 ˚C
24 hrs 48 hrs 72 hrs
Main unit Individual
-
input priority input priority
N/A Available -
N/A Available -
N/A Available -
Setting Data 0 to 14 -- > Outdoor temperature correction -7 ˚C to 7 ˚C
Setting Data 0 to 14 -- > Room temperature correction -7 ˚C to 7 ˚C
Dip-SW
Pattern A Pattern B
priority
Setting Data 0 to 7 -- > Temperature gap 0 ˚C to 7 ˚C
Setting Data 0 to 15 -- > Lowest outdoor temperature 10 ˚C to 25 ˚C
Setting Data 0 to 15 -- > Lowest indoor temperature 15 ˚C to 30 ˚C
N/A 1 level up 2 level up 3 level up 4 level up
N/A 1 level up 2 level up 3 level up 4 level up
EA fan SA fan
Dip-SW
monitor monitor
priority
output output
Operation
By-pass
Dip-SW monitor
monitor
priority output for
output
Pre-heater
0 ˚C -1 ˚C -2 ˚C
1 hr 2 hrs 3 hrs
Dip-SW Fan speed Fan speed
priority 4 3
Dip-SW Fan speed Fan speed
priority 2 1
Dip-SW
N/A Pattern X
priority
- Initialize -
-E series.
5
Setting Data
3 4 5
Indicator
available
- -
Fan power
up available
- - -
Return to the
state before - -
interruption
Supply 2
- -
down
Exhaust 2
- -
down
- - -
30 min - -
- - -
No change - -
External
OFF inter-
input given -
lock
priority
- - -
-
3 ˚C 4 ˚C 5 ˚C
- - -
- - -
- - -
- - -
- - -
Free
- -
setting
-
-
SA fan
monitor
- -
with delay
operation
- - -
-3 ˚C -4 ˚C -5 ˚C
4 hrs 5 hrs -
- - -
- - -
Pattern Y Pattern Z -
- - -
Factory DIP-SW
setting No.
6 7
- - 0 5-5
- - 0 N/A
- - 0 5-4
- - 0 2-4
- - 0 2-5
- - 0 N/A
- - 0 5-1
- - 0 5-3
5-3
- - 0
5-9
5-7
- - 0
5-8
- - 0 2-2
- - 0 N/A
6 ˚C 7 ˚C 5 N/A
2 N/A
- - 0 N/A
- - 0 N/A
- - 0 N/A
- - 0 N/A
- - 0 N/A
7 N/A
0 N/A
7 N/A
7 N/A
- - 0 2-7
0 N/A
6 N/A
1 N/A
- - 0 N/A
- - 0 N/A
2-8
- - 0
5-2
- - 0 5-6
-6 ˚C -7 ˚C 0 N/A
- - 0 N/A
- - 0 2-9
- - 0 2-10
2-3
- - 0
2-6
- - 0 N/A