Maintenance And Storage - Hudora 72166 Aufbau- Und Gebrauchsanleitung

INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING THIS PRODUCT!
Please read these instructions carefully. The instructions are an integral component
of the product. Therefore, please store them and the packaging carefully in case
questions arise in the future. Please always include these instructions when handing
on the product to a third party. This product must be assembled by an adult. This
product is designed for private/domestic use only. This product is not designed for
commercial/industrial use. The use of the product requires certain capabilities and
skills. Always adjust according to the age of the user and use for the purpose it has
been designed for.
TECHNICAL SPECIFICATIONS
Item: Nest Swing Square 110
Item No.: 72166
Maximum carrying capacity: 120 kg
Dimension: ca. 110 x 70 cm
Minimum age for use: 3 years
Purpose: Device powered by muscle power, for swinging in a
sitting or lying position.
If you have assembly problems or would like further information on the product, we
have all you need and more at http://www.hudora.de/.
CONTENTS
1 x Nest swing (cf. part list on page 2)
1 x These instructions
Other parts which may be included with the delivery in some circumstances are not
required.
SAFETY INSTRUCTION
• WARNING! Only for domestic use.
• WARNING! To be used under the direct supervision of an adult.
• WARNING! Not suitable for children under 36 months. Danger of falling!
• WARNING! Not suitable for children under 36 months due to long cords! Strangu-
lation hazard.
• WARNING! Suitable for outdoor and indoor use!
• The owners of the swing as well as the competent supervisory personnel are
responsible for ensuring that all users follow the instructions in the operation
manual.
• Do not make any technical modifications.
• Changes to the original product must only be carried out according to manu-
facturer specifications.
• No one is permitted to gain access to the swing area during use.
• Never stand or kneel on the swing.
• Always hold yourself firmly with both hands.
• No objects of any kind must be in the vicinity of the swing zone (trees, walls,
fences, clotheslines).
• Make sure that you have a safety clearance of at least 2 m (front and back)
beyond the maximum reach of the swing and make sure the ground is level
and shock absorbing (e.g. grass) without any sharp edges or pointed objects,
obstacles, inclines, levels, steps or hard surfaces (e.g. concrete) etc.
• Clearance to stationary components on the side, such as the swing scaffolding
must be at least 40 cm.
• Swinging components, such as a neighboring swing must be placed at a distance
of at least 60 cm.
• Maximum raised height must not exceed 2.5 meter as measured from the ground.
• In idle mode, the swing must be at least 40 cm and maximally 60 cm from the
ground.
• You should never install a swing in such a way that the user could be blinded by
sun rays.
• The self-locking effect of the self-locking nuts or else lacquer can subside after
repeated loosening and tightening of the connection elements.
• When permanently irradiated with UV light, the material ages significantly faster.
To avoid premature aging and thereby extend the service life, you should always
store the product in a dry and dark place when not in use. Do not permanently
expose the product to wind, moisture, extreme temperatures or sunlight.
All images are examples of the design.
INSTRUCTIONS ON ASSEMBLY
Prior to installation, carefully select and check the location where you will install the
swing. Please make sure that the swing carrier is adequately stable. Please also take
into account that swinging produces centrifugal forces that can put a lot of strain on
the swing carrier. Please consult an expert (statics expert, architect, carpenter) and
ask how much load your swing carrier can tolerate.Suspension connectors shall be
of a design that will prevent unintentional disconnection. After removing the product
from its packaging, please check it for completeness. Please thereby note that most
items are pre-assembled. Spread out the nest of the swing (1) on the floor. Insert a
part of the foam-covered tubular frame (2 + 3) into each of the tunnel loops of the
nest (1). Guide the two angled tubes (2) each on the short side through the tunnel
loops (Fig. 1), and the two straight tubes (3) each on the long side (Fig. 2). The tubes
are not yet connected to each other. First the two swing cables (4) are attached. A
swinging rope is fitted (Fig. 3 + 4) on each long side of the nest swing. To do this,
proceed as follows: First insert one of the two connection pieces on the rope to the
end of one of the angled tubes (2). Make sure that the ribbed interior side (side B) of
the connection piece is slipped onto the tube. Then run the straight tube (3) from the
other side (side A) through the connecting piece into the angled tube (2) and connect
them by pushing the buttons. Proceed in the same way with the same rope on the
other side of the straight tube (3). Now place the second rope on the opposite side of
the nest swing accordingly. Now you can hang the mounted nest swing (Fig. 5) with
the help of the retaining rings (5) onto a suitable swing carrier.
HANGING DEVICE AND ADJUSTMENT
The hanging points must be at least as far apart as the swing seat + 100mm. The
swing is packaged with two ropes and adjustment eyelets (6), so that the height of
the swing can be variably aligned with any suitable hanging device. The swing rope
(4) can be lengthened or shortened by pushing or pulling it through the adjustment
loops (4). The hanging swing can now be individually adjusted. No one should sit on
the swing while making the adjustments. When extending or reducing the length of
the swing ropes please make sure that the ropes remain equally long at all times. If
the lengths of the ropes differ, this will lead to circular pendulum movements of the
swing. Make sure that swing is set up in such a way that the person using the swing
cannot reach the ground with the tips of his or her toes. If in doubt, perform a few
gentle test swings.

MAINTENANCE AND STORAGE

Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and after
each use. Do not make any structural changes. For your own safety, please use origi-
nal spare parts only. These can be sourced from HUDORA. If parts become damaged
or if sharp edges or corners should develop, the product may not be used any more.
If in any doubt, please contact our service team (http://www.hudora.de/service/).
Store the product in a safe place where it is protected from the elements, cannot be
damaged, and cannot injure anyone.
You should also replace all the plastic parts after a maximum of 5 years to prevent a
possible failure of these parts.
Check the product for damage or traces of wear and tear before and after each use.
We also recommend before each use:
• to check for the firm sitting of nuts and bolts, tighten if necessary
• to lubricate moving parts in order to minimize wear.
• to check all covers of screws and sharp edges and replace if necessary
• to replace defective parts according to the manufacturer's instructions
• to check swing seats, chains, ropes and other means of attachments for evidence
of deterioration
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appropriate collection
point in your area. Local waste management companies will be able to answer your
questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however, we
put just as much effort into rectifying them. You can find numerous information on
the product, replacement parts, solutions to problems and lost assembly manuals at
http://www.hudora.de/service/.
7/12