Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
2.5S -mod/A
2.5S -mod/C
2.5W
2.5W -mod/A
2.5W-mod/C
2.5W GASTRO
2.5W GASTRO-mod/A
2.5W GASTRO-mod/C
NWS
NWS-mod/A
NWS-mod/C
NWW
NWW-mod/A
NWW-mod/C
NZW
NZW-mod/A
NZW-mod/C
The above-mentioned technical data also concern "DRE" display cabinets. However, the weight of the device shall be
slightly higher than the one stated in the table!
3. PREPARING THE DEVICE FOR EXPLOITATION
3.1. Requirements concerning the place of installation
• Verify whether the cross section of feeding conduits is proper for power consumption of the installed device.
• It is forbidden to connect the device by extension rods or dividers.
• The device should be connected to the separate, properly made electric circuit with plug-in socket with protecting
pin (according to PBUE /Regulations concerning Electric Equipment Construction/)
The device may be actuated solely after confi rmation of the fi re protection effi ciency with results of measu-
res performed according to binding regulations!
3.2. Connection and actuation
• Unpack the device and remove the wooden platform from the basis (does not concern moving devices) Fig.3 (p.18)
• The device should be placed on an even and on a suffi ciently hard base, and then level it with the help of levelling feet.
In case of moving devices it is necessary to immobilise wheels in order to prevent their movement during exploitation
Fig.4 (p.18)
• Remove the protection foil from the elements of the device (f. ex. from the inside of the device, display shelves and
front fender beam)
• If the user shall obtain a device partially disassembled to secure it during transportation, perform the following ope-
rations:
1. Mount display shelves, hanging them on aluminium angle sections Fig.5/4;5 (p.18)
2. Mount glass sides Fig.6/2 (p.19)
NOTE: In case of "Gastro" display cabinets, it is necessary to take out the universal salad tank from the display cabinet
before mounting the glass side Fig.5/1 (p.18), in order to obtain free access to the ABS side and to easily screw the
glass side with holding downs of the glass Fig.6/1 (p.19).
3. Mount ABS lamp hole plug according to Fig.6/3 (p.19)
4. Mount the casing of lamp conduit Fig.6/7 (p.19)
Move the casing of lamp conduit to the back of the glass side, in order to hide the conduit coming out of the lamp in
the casing and to place it on the internal part of the glass side!
5. (Concerns only "GASTRO" displays) place universal salad tank in the display cabinet. Place cross-bars under GN
containers in the module tank, and then place GN containers according to Fig.2 (p.15)
6. Mount glass shelves according to Fig.6/5 (p.19)
7. Mount front screen Fig.6/9 (p.19)
www.igloo.pl
230/50
2,5
230/50
0,3
230/50
3,2
230/50
3,2
230/50
0,5
230/50
3,2
230/50
3,2
230/50
0,5
230/50
1,0
230/50
1,0
230/50
0,1
230/50
1,2
230/50
1,2
230/50
0,2
230/50
1,5
230/50
1,5
230/50
0,2
60
8,0
60
0,8
60
10,2
60
10,2
60
1,6
60
10,2
60
10,2
60
1,6
18
3,2
18
3,2
18
0,3
18
3,9
18
3,9
18
0,5
15
4,9
15
4,9
15
0,5
-
50
350
50
-
50
-
50
450
50
-
-
-
-
450
-
-
50
-
50
350
50
-
50
-
50
450
50
-
50
-
50
450
50
User manual Santiago
en
275
257
295
275
257
295
275
257
180
165
145
180
165
145
155
140
120
17
Werbung
Kapitel
Inhaltsverzeichnis
