Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Product overview
1
2
5
1 Power LED POWER
2 LED indicators for the connections (16x)
3 RJ45 connections 1 to 16
4 Ventilation openings (on both sides, not shown)
5 Threaded holes on both sides for mounting bracket (not shown)
6 Mains connection 12 V
1 A
7 Earth connection SWITCH GND
Setup and installation
Before installation, remove any connected devices and the power adapter to the Gigabit switch.
a) Installation
You can use the Gigabit switch on a horizontal heat-resistant surface using the feet. To install
on a flat surface, proceed as follows:
• Pull the supplied feet individually from the support strip and affix them symmetrically with
the adhesive side (base of the pyramid stub) on the base of the product. Distribute the feet
symmetrically at the four corners as far from the centre of the housing as possible to ensure
a stable, wobble-free position.
• When installing the product, ensure that there is enough space on all sides for sufficient air
circulation for cooling (approx. 10 cm distance to walls and other objects).
b) Installation into a server rack
You can install the Gigabit switch into a standard 19" server rack with the mounting bracket
supplied. To install into a server rack, proceed as follows:
• Attach the mounting bracket to the threaded holes (5) on the housing using the screws
supplied. You will need a Philips screwdriver to do this.
• Then, install the pre-installed Gigabit switch into the rack using the appropriate server rack
screws (not included).
Ensure that there is a mains socket near to where the switch is installed so that you
can plug in the power adapter.
3
3
7
6
Setup
a) Data connections
4
The maximum length of the network cable can be up to 100 m.
5
b) Mains connection
• Connect the low-voltage plug on the power adapter to the mains socket 12 V 1 A (6).
• Plug the mains plug of the power adapter into an appropriate mains socket to connect the
power supply.
• The mains LED POWER (1) lights up. The Gigabit switch is correctly supplied with power.
• Connect the earth connection SWITCH GND (7) via a cable connected to the earth of the
server rack into which Gigabit switch is installed. Screw in a curved cable eyelet with the aid
of a suitable Phillips screwdriver.
If the function LED indicators (2) do not light up, check that the connections are
firmly seated. If the mains LED POWER (1) does not light up, check the power
supply (power adapter and connections).
c) LED indicators
LED name
Power
Number 1 - 16
Care and cleaning
• This product does not require maintenance. Under no circumstances should you service any
of the components in the interior of the product, therefore never open it.
• Always disconnect the product from the power supply before cleaning it.
• Disconnect any cables from the product before cleaning.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the housing or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product. Do not press too hard on the housing, as this
can lead to scratch marks.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to protection of the environment.
You can directly connect up to 16 network
devices with appropriate connectors via RJ45
connections and cables.
Colour
State
Meaning
Green
On
Power supply on
Off
Power supply off
Green
On
1000 MBit/s device connected to this
connection
Off
Network device not connected
Flashing
Data transfer (send/receive) at a speed of up
to 1000 MBit/s
Orange
On
Device with 10/100 MBit/s transfer speed
connected to this connection
Off
Network device not connected
Flashing
Data transfer (send/receive) at a speed of up
to 10/100 MBit/s
Werbung
Inhaltsverzeichnis
