Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
6 Product overview
6.1 HDMI switch
1
4
5
6
7
1 Power Jack: Connect to the included
power adaptor
2 HDMI IN1/IN2/IN3/IN4: Connect to source
device's HDMI
3 HDMI OUT: Connect to HDMI display
4 Audio: Audio output
5 Select: Video mode selection key
6 Beep: Audio switching key
7 Mode: Upscale 720P signal into 1080P or
downscale 1080P signal into 720P.
8 IR: Infrared receiver
6.2 Remote control
B
C
A ON/OFF: Power on/off switch
B Rset: Reset to CH1 mode
C H/S: Upscale 720P signal into1080P or downscale
A
D
D select: Video mode selection
E
E Mode select button (Ch1-Ch4): Single screen
F
G
F
G Audio Select button (♪1- ♪4): Press these buttons
H
H Input selection button (IN1-IN4): Input source
7 Installing the battery
1. Remove the battery cover from the back of the remote control.
2. Install a CR2025 battery in the remote control.
3. Refit the battery cover to the remote control.
8 Connecting source and display devices
1. Connect the source devices (example: DVD player, games console) to the HDMI input
ports HDMI IN using suitable HDMI cables.
2. Connect the display device to the HDMI output port HDMI OUT using a suitable HDMI
cable.
9 Operation
1. Connect the power adaptor to the power jack of the HDMI switch.
2. Connect the power adaptor to the mains supply.
9.1 Setting the display mode
Available modes
1
The product provides 5 multi-viewer display modes as shown below.
MODE1: The four HDMI input sources are displayed in 2x2 on one screen
MODE2: The four HDMI input sources are displayed H-spilt on one screen
MODE3: The four HDMI input sources are displayed with one bigger and three smaller
windows on one screen
MODE4: The two HDMI input sources are displayed in 2x1 on one screen
MODE5: This is the full screen mode, press IN1 ~ IN4 button on the remote control, this will
select the corresponding channel displayed in full screen as a seamless switcher.
2
3
8
9
10
11
12
13
9 Audio capture: The indicator is on when
the audio channel is open, if the indicator
is off, the audio channel is closed
10 Not capture: Constant light when
stopping video collection, collection does
not light up at the start
11 Capture: Flicker during video capture, not
on when stopping video collection
12 POWER: Power led
13 USB 3.0: Collection outlet
1080P signal into 720P
specified mode
: Quad multi-viewer mode
to select the audio from the input sources
selection button
Procedure
2
1. Press the select button on the remote control to select the intended display mode.
9.2 Video/audio capture
Important: The computer must have the following hardware configuration requirements:
CPU: PC i5-3400 or above; NB i7-3537u 2.0 GHz or above.
Display card: PC NVIDIA gt630 or above; NC NVIDIA gt735m or above.
Storage: 4 G RAM
1. Connect the computer to the USB port USB 3.0 using a suitable USB data cable (at least
USB 3.0 rated).
2. Open a suitable video capture software (VLC, OBS, amcap, etc) on the computer.
3. Create a new video and audio source, select 'OK' to create on each window.
4. Select 'video capture device'.
5. Select 'audio capture device'.
6. Drag the red area to set the screen size.
7. Studio Mode is dual window working mode, the left is preview window, and right is
capture window. The user can adjust the size of the video capture window in the preview
window, then click transition to apply the adjusted size to the capture window.
Werbung
Inhaltsverzeichnis
