Conformity Declaration; Specified Use; General Safety Instructions; Special Safety Instructions - Metabo STEB 70 Quick Originalbetriebsanleitung

Original instructions

1. Conformity Declaration

We, being solely responsible, hereby declare that
these jigsaws conform to the standards and direc-
tives specified on page 3.

2. Specified Use

The machine is suitable for sawing non-ferrous
metals and sheet steel, wood and similar materials,
plastics and similar materials. Any other use is not
permitted.
The user bears sole responsibility for damage
caused by improper use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.

3. General Safety Instructions

For your own protection and for the
protection of your electrical tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety warn-
ings and instructions may result in electric shock,
fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your electrical tool only together with these
documents.

4. Special Safety Instructions

Hold power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes
(e.g. using a metal detector).
Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust may
cause allergic reactions and/or respiratory diseases
to the operator or bystanders.
Certain kinds of dust are classified as carcinogenic
such as oak and beech dust especially in
conjunction with additives for wood conditioning
(chromate, wood preservative). Material containing
asbestos must only be treated by specialists.
- Where the use of a dust extraction device is
possible it shall be used.
- To extract dust more efficiently, use the protective
cap (9) and a suitable Metabo vacuum cleaner
together with this tool.
- The work place must be well ventilated.
- The use of a dust mask of filter class P2 is
recommended.
Follow national requirements for the materials you
want to work with.
During work, the workpiece must lay flat and be
secured against moving, e.g. using clamps.
Do not try to saw extremely small workpieces.
When sawing, the footplate must make secure
contact with the workpiece.
When interrupting a cut for any reason, release the
trigger and hold the saw motionless in the material
until the saw blade comes to a complete stop. Never
attempt to remove the saw from the workpiece while
the saw blade is in motion or kickback may occur.
Do not switch the machine on while the saw blade is
touching the workpiece. Let the saw blade reach full
speed before making a cut.
When restarting a saw in the workpiece, centre the
saw blade in the kerf and check that saw teeth are
not engaged into the material. If the saw blade
seizes, it may kickback from the workpiece when
the saw is restarted.
Keep hands well away from the sawing area and the
saw blade. Do not reach underneath the workpiece.
Remove chips and similar material only with the
machine at standstill.
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
Danger of injury due to the sharp jigsaw blade. After
stopping work, the jigsaw blade may still be hot.
Wear protective gloves.
5. Overview
See page 2.
1 Clamping lever for securing the saw blade
2 Saw blade support roller
3 Saw blade
4 Screw for adjusting the footplate
5 Footplate
6 Switch button on the chip blower
7 Adjustment lever for pendulum motion
8 Anti-splintering footplate insert
9 Protective cap
10 Saw blade clamping fixture
11 Protective rod for preventing unintentional
contact with the saw blade
12 Setting wheel for speed adjustment
13 Trigger
14 Lock button for continuous activation
15 Hexagon spanner
16 Extractor connection piece
17 Curved support plate indicating preset cutting
angle
ENGLISH en
9